manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1218

GPIO Registers

www.ti.com

1218

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

General-Purpose Input/Outputs (GPIOs)

17.5.14 GPIOODR Register (Offset = 0x50C) [reset = 0x0]

GPIO Open Drain Select (GPIOODR)

The GPIOODR register is the open drain control register. Setting a bit in this register enables the open-
drain configuration of the corresponding GPIO pad. When open-drain mode is enabled, the corresponding
bit should also be set in the GPIO Digital Enable (GPIODEN) register (see

Section 17.5.18

).

Corresponding bits in the drive strength and slew rate control registers (GPIODR2R, GPIODR4R,
GPIODR8R, and GPIOSLR) can be set to achieve the desired fall times. The GPIO acts as an input if the
corresponding bit in the GPIODIR register is cleared. If open drain is selected while the GPIO is
configured as an input, the GPIO will remain an input and the open-drain selection has no effect until the
GPIO is changed to an output.

When using the I

2

C module, in addition to configuring the data pin to open drain, the GPIO Alternate

Function Select (GPIOAFSEL) register bits for the I

2

C clock and data pins should be set (see examples in

Section 17.4

).

NOTE:

This register has no effect on port pins PL6 and PL7.

GPIOODR is shown in

Figure 17-18

and described in

Table 17-21

.

Return to

Summary Table

.

Figure 17-18. GPIOODR Register

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

ODE

R-0x0

R/W-0x0

Table 17-21. GPIOODR Register Field Descriptions

Bit

Field

Type

Reset

Description

31-8

RESERVED

R

0x0

7-0

ODE

R/W

0x0

Output Pad Open Drain Enable

0x0 = The corresponding pin is not configured as open drain.

0x1 = The corresponding pin is configured as open drain.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands