manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

McBSP2

7-105

MPU Public Peripherals

Table 7–78 describes the McBSP2 pins. Table 7–79 lists the McBSP2 regis-
ters. Figure 7–44 shows the McBSP2 interface.

Table 7–78. McBSP2 Pin Descriptions

Pin

I/O Direction

Description

MCBSP2.CLKR

In/out

Receive clock

MCBSP2.CLKX

In/out

Transmit clock

MCBSP2.DR

In

Data input

MCBSP2.DX

Out

Data output

MCBSP2.FSR

In/out

Receive frame synchronization

MCBSP2.FSX

In/out

Transmit frame synchronization

The McBSP2 base address is FFFB:1000 (MPU memory map).

Table 7–79. McBSP2 Registers  

Name

Description

Offset

DRR2 (15:0)

Data receive register 2

0x00

DRR1 (15:0)

Data receive register 1

0x02

DXR2 (15:0)

Data transmit register 2

0x04

DXR1 (15:0)

Data transmit register 1

0x06

SPCR2 (15:0)

Serial port control register 2

0x08

SPCR1 (15:0)

Serial port control register 1

0x0A

RCR2 (15:0)

Receive control register 2

0x0C

RCR1 (15:0)

Receive control register 1

0x0E

XCR2 (15:0)

Transmit control register 2

0x10

XCR1 (15:0)

Transmit control register 1

0x12

SRGR2 (15:0)

Sample rate generator register 2

0x14

SRGR1 (15:0)

Sample rate generator register 1

0x16

MCR2 (15:0)

Multichannel register 2

0x18

MCR1 (15:0)

Multichannel register 1

0x1A

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Brand: Cateye Pages: 15
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
QuickLink QL-CXS Installation Manual preview
QL-CXS
Brand: QuickLink Pages: 8
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Brand: Galaxy Pages: 30
Active Communications ACS express Quick Start Manual preview
ACS express
Brand: Active Communications Pages: 10
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Brand: Kaya Instruments Pages: 48
Ampro Corporation LITTLE BOARD P5X Hardware User Manual preview
LITTLE BOARD P5X
Brand: Ampro Corporation Pages: 121
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
ADTRAN ENHANCED PSD 239 H2R Product Manual preview
ENHANCED PSD 239 H2R
Brand: ADTRAN Pages: 2
IEI Technology PUZZLE-IN005 User Manual preview
PUZZLE-IN005
Brand: IEI Technology Pages: 106
Arctic Freezer i32 Welcome Manual preview
Freezer i32
Brand: Arctic Pages: 7
Alphacool NexXxoS GPX-N 970 M03 Instruction Manual preview
NexXxoS GPX-N 970 M03
Brand: Alphacool Pages: 2

Brands by name

Popular brands

Load more brands