Texas Instruments OMAP36 Series Technical Reference Manual Download

Page: 645 / 3738

Public Version

www.ti.com

PRCM Register Manual

Table 3-489. PRM_VP1_STATUS

Address Offset

0x0000 00C4

Physical Address

0x4830 72C4

Instance

Global_Reg_PRM

Description

This register reflects the idle state of the Voltage Processor 1 (VDD1). This register is read only and
automatically updated.

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

RESERVED

VPINIDLE

Bits

Field Name

Description

Type

Reset

31:1

RESERVED

Write 0s for future compatibility. Read is undefined.

0x00000000

VPINIDLE

Voltage Processor 1 idle status.

0x1

0x0: The Voltage Processor 1 is processing.

0x1: The Voltage Processor 1 is in idle state.

Table 3-490. Register Call Summary for Register PRM_VP1_STATUS

PRCM Basic Programming Model

•

Voltage Processor Registers

[0]

•

PRM_VP_STATUS (Voltage Processor Status Register)

[1]

PRCM Register Manual

•

Global_Reg_PRM Register Summary

[2]

Table 3-491. PRM_VP2_CONFIG

Address Offset

0x0000 00D0

Physical Address

0x4830 72D0

Instance

Global_Reg_PRM

Description

This register allows the configuration of the Voltage Processor 2 (VDD2).

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

ERROROFFSET

ERRORGAIN

INITVOLTAGE

RESERVED

INITVDD

VPENABLE

TIMEOUTEN

FORCEUPDATE

Bits

Field Name

Description

Type

Reset

31:24

ERROROFFSET

Offset value in the Error to Voltage converter (two's

0x00

complement number).

23:16

ERRORGAIN

Gain value in the Error to Voltage converter (two's

0x00

complement number).

15:8

INITVOLTAGE

Set the initial voltage level of the SMPS. It must be

0x00

reconfigured before SmartReflex is enabled around a
new OPP.

7:4

RESERVED

Write 0s for future compatibility. Read is undefined.

0x0

645

SWPU177N – December 2009 – Revised November 2010

Power, Reset, and Clock Management

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands