Texas Instruments OMAP36 Series Technical Reference Manual Download

Page: 2888 / 3738

Public Version

UART/IrDA/CIR Integration

www.ti.com

19.3.1.3 Software Reset

The UARTi.

SYSC_REG

[1] SOFTRESET bit controls the software reset; writing 1 to this bit triggers a

software-reset functionally equivalent to hardware reset.

19.3.1.4 Power Domain

Each UART in the CORE or PER power domain can dynamically switch between available voltage levels
(see

Table 19-13

Table 19-13. Power Domain

Peripherals

Power Domain

UART1

CORE

UART2

CORE

UART3

PER

UART4

PER

19.3.2 Hardware Requests

19.3.2.1 Interrupts

Table 19-14

describes the UART interrupt mappings.

Table 19-14. Interrupt Mapping to MPU Subsystem

IRQ

Source

Description

M_IRQ_72

UART1_IRQ

UART module 1 interrupt to MPU

M_IRQ_73

UART2_IRQ

UART module 2 interrupt to MPU

M_IRQ_74

UART3_IRQ

UART module 3 interrupt to MPU

M_IRQ_80

UART4_IRQ

UART module 4 interrupt to MPU

Table 19-15. Interrupt Mapping to IVA2.2 Subsystem

IRQ

SOURCE

DESCRIPTION

IVA2_IRQ[15]

UART3_IRQ

UART module 3 interrupt to IVA2.2 subsystem

19.3.2.2 DMA Requests

Table 19-16

describes the UART DMA requests.

Table 19-16. UART DMA Requests to System DMA

DMA

(1)

Source

Description

S_DMA_48

UART1_DMA_TX

UART module 1 transmit request

S_DMA_49

UART1_DMA_RX

UART module 1 receive request

S_DMA_50

UART2_DMA_TX

UART module 2 transmit request

S_DMA_51

UART2_DMA_RX

UART module 2 receive request

S_DMA_52

UART3_DMA_TX

UART module 3 transmit request

S_DMA_53

UART3_DMA_RX

UART module 3 receive request

S_DMA_80

UART4_DMA_TX

UART module 4 transmit request

S_DMA_81

UART4_DMA_RX

UART module 4 receive request

(1)

This table assumes that DMA mode 1 is used.

2888

UART/IrDA/CIR

SWPU177N – December 2009 – Revised November 2010

«
...
2886
2887
2888
2889
2890
...
»

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands