Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 2597 / 3738

background image

Public Version

www.ti.com

SCM Register Manual

Bits

Field Name

Description

Type

Reset

5:4

PRG_HDQ_LB

Effective TL length and farend capacitive load controls.

RW

0x0

This bit allows control of programmable drive/slew control on
IO cell. Format used in the field name below is:
(programmable_group_name)_(configurable_pin on IO cell)
See

for the allowed SC vs LB bit field

combinations !

3:2

PRG_HDQ_SC

Slew rate control bits.

RW

0x0

Format used in the field name below is :
(programmable_group_name)_(configurable_pin on IO cell)
See

for the allowed SC vs LB bitfield

combinations !

1

PRG_MCSPI1_MIN_CFG_LB

Format used in the field name below is :

RW

0

(programmable_group_name)_(configurable_pin on IO cell)
Far end load setting.Transmission Line (TL) characteristic
impedance is 50 Ohm, TL capacitance =1pF / cm:
0x0: Far end load = [1pF-10pF] / TL length=[1cm-6cm] 0x1:
Far end load = [10pF-16pF] / TL length=[1cm-6cm]

0

PRG_MCSPI1_CS1_LB

Format used in the field name below is :

RW

0

(programmable_group_name)_(configurable_pin on IO cell)
Far end load setting.Transmission Line (TL) characteristic
impedance is 50 Ohm, TL capacitance =1pF / cm:
0x0: Far end load = [1pF-10pF] / TL length=[1cm-6cm] 0x1:
Far end load = [10pF-16pF] / TL length=[1cm-6cm]

Table 13-149. Register Call Summary for Register CONTROL_PROG_IO2

SCM Functional Description

•

Signal Integrity Parameter Controls Overview

•

Device Interfaces Signal Group Controls Mapping

:

[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19]

SCM Programming Model

•

I2C I/O Internal Pullup Enable

:

•

MCBSP2 I/O Far End Load Settings

:

•

MCSPI1 I/O Far End Load Settings

SCM Register Manual

•

SCM Register Summary

:

Table 13-150. CONTROL_MEM_RTA_CTRL

Address Offset

0x0000 019C

Physical Address

Instance

GENERAL

0x4800 240C

Description

control_mem_rta_ctrl register description

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

HD_MEM_RTA_SEL

Bits

Field Name

Description

Type

Reset

31:1

RESERVED

Reserved field

R

0x0000 0000

0

HD_MEM_RTA_SEL

Device level control for selection of RTA feature of HD

RW

0x1

memories in the device
1 : RTA enabled
0 : RTA disabled

2597

SWPU177N – December 2009 – Revised November 2010

System Control Module

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
2595
2596
2597
2598
2599
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: TC Electronic Pages: 2

Brand: Paradyne Pages: 112

Brand: Acqiris Pages: 22

Brand: Dantel Pages: 62

Brand: MC Pages: 21

Brand: Lanner Pages: 78

Brand: Z3 Technology Pages: 87

Brand: Digi Pages: 116

LIQMAX III ELC-LMT120-ARGB

Brand: ENERMAX Pages: 32

Brand: NCR Pages: 15

Brand: Vecow Pages: 61

Brand: UNICORECOMM Pages: 19

Brand: ICS ELECTRONICS Pages: 4

Brand: Arctic Pages: 7

NexXxoS GPX-N 970 M03

Brand: Alphacool Pages: 2

Brand: CAME Pages: 14

Brand: AG Pages: 10

Brand: Jatontec Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands