Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 2397 / 3738

background image

Public Version

www.ti.com

SDMA Register Manual

Table 11-58. DMA4_CDEIi

Address Offset

0x0000 00AC + (i* 0x60)

Index

i = 0 to 31

Physical Address

0x4805 60AC + (i* 0x60)

Instance

SDMA

Description

Channel Destination Element Index (Signed)

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

CHANNEL_DST_ELMNT_INDEX

Bits

Field Name

Description

Type

Reset

31:16

RESERVED

Reserved. Write 0s for future compatibility. Read returns

RW

0x0000

0.

15:0

CHANNEL_DST_ELMNT_INDEX Channel destination element index

RW

0x----

Table 11-59. Register Call Summary for Register DMA4_CDEIi

SDMA Register Manual

•

SDMA Register Summary

:

Table 11-60. DMA4_CDFIi

Address Offset

0x0000 00B0 + (i* 0x60)

Index

i = 0 to 31

Physical Address

0x4805 60B0 + (i* 0x60)

Instance

SDMA

Description

Channel Destination Frame Index (Signed) or 16-bit Packet size

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

CH_DST_FRM_IDX_OR_16BIT_PKT_ELNT_NBR

Bits

Field Name

Description

Type

Reset

31:0

CH_DST_FRM_IDX_OR_

Channel destination frame index value if destination

RW

0x--------

16BIT_PKT_ELNT_NBR

address is in double index mode. Or if fs=bs=1 and
DMA_CCR[SEL_SRC_DST_SYNC]=0; the bit field [15:0]
gives the number of element in packet. The field [31:16]
is unused for the packet size..

Table 11-61. Register Call Summary for Register DMA4_CDFIi

SDMA Functional Description

•

Packet Synchronization

:

[0] [1] [2] [3]

SDMA Basic Programming Model

•

Hardware-Synchronized Transfer

:

SDMA Register Manual

•

SDMA Register Summary

:

2397

SWPU177N – December 2009 – Revised November 2010

SDMA

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
2395
2396
2397
2398
2399
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: Barracuda Networks Pages: 2

Brand: Hal Communications Pages: 25

Brand: 3Com Pages: 2

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: LAWO Pages: 154

EK-Vector Radeon RX5700 + XT Backplate

Brand: ekwb Pages: 7

SteelCentral NetExpress

Brand: Riverbed Pages: 38

Brand: Telit Wireless Solutions Pages: 113

Brand: Seattle Computer Products Pages: 31

Brand: Lanner electronics Pages: 59

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: VideoWave Pages: 12

MTDOT-868 Series

Brand: Multitech Pages: 60

Fibe-Air IP-10G

Brand: Ceragon Pages: 71

Brand: Enterasys Pages: 2

Brand: Rajant Pages: 93

Brand: DAPAudio Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands