Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 1811 / 3738

background image

Public Version

www.ti.com

Display Subsystem Register Manual

Table 7-114. Enable Command Mode and Automatic TE (continued)

Steps

Register/Bit Field/Programming

Value

Wait until PACKET_SENT_IRQ = 1.

DSI_VC1_IRQSTATUS[2] PACKET_SENT_IRQ

Write 1 to clear PACKET_SENT_IRQ.

DSI_VC1_IRQSTATUS[2] PACKET_SENT_IRQ

0x1

7.6.5.1.6 Send Frame Data to LCD Panel Using Automatic TE

summarizes the steps to send a frame data to the LCD panel using automatic TE.

Table 7-115. Send Frame Data to LCD Panel Using Automatic TE

Steps

Register/Bit Field/Programming

Value

Enable the transfer between DISPC and

[0] LCDENABLE

0x1

DSI. Reset after the transfer is done.

Specify the number of bytes to send. When
DCS insertions is used, word count (WC)

DSI_VC0_TE[23:0] TE_SIZE

(WC+1)*LPP

must include this one DCS byte.

Set up long packet header. Send 0x39
DCS long write/write_LUT command
packet used to send larger blocks of data

DSI_VC0_LONG_PACKET_HEADER[31:0] HEADER

(WC+1) << 8 + 0x39

to a display module that implements a
DCS.

Enable TE control.

DSI_VC0_TE[30] TE_EN

0x1

Wait until RX FIFO is empty,

DSI_VC1_CTRL[20] RX_FIFO_NOT_EMPTY

0x0

RX_FIFO_NOT_EMPTY = 0.

Wait until TX FIFO is not full.

DSI_VC1_CTRL[16] TX_FIFO_FULL

0x0

TX_FIFO_FULL = 0.

Enable first BTA to give bus possession to

DSI_VC1_CTRL[6] BTA_EN

0x1

the display module.

Wait until BTA IRQ.

DSI_VC1_IRQSTATUS[5] BTA_IRQ

0x1

Write 1 to clear BTA IRQ.

DSI_VC1_IRQSTATUS[5] BTA_IRQ

0x1

Enable second BTA to get the TE trigger.

DSI_VC1_CTRL[6] BTA_EN

0x1

Wait until BTA IRQ.

DSI_VC1_IRQSTATUS[5] BTA_IRQ

0x1

Write 1 to clear BTA IRQ.

DSI_VC1_IRQSTATUS[5] BTA_IRQ

0x1

Wait until transfer is complete.

DSI_VC0_TE[30] TE_EN

Read 0x0

7.7

Display Subsystem Register Manual

CAUTION

•

The DISS, DISPC, RFBI, and VENC registers have no register data width
access restriction and can be accessed in 8-bit, 16-bit and 32-bit access.

•

The DSI complex I/O and DSI PLL control module registers are limited to
32-bit data access; 16-bit and 8-bit data accesses are not allowed and can
corrupt register content.

•

The DSI protocol engine DSS.

DSI_VCn_LONG_PACKET_HEADER

and

DSS.

DSI_VCn_SHORT_PACKET_HEADER

registers are limited to 32-bit

data access; 16-bit and 8-bit data accesses are not allowed and can corrupt
register content.

•

The DSI protocol engine DSS.

DSI_VCn_LONG_PACKET_PAYLOAD

register is limited to 32-bit and 16-bit data access; 8-bit data accesses are
not allowed and can corrupt register content.

•

All other DSI protocol engine registers have no register data width access
restriction and can be accessed in 8-bit, 16-bit and 32-bit access.

1811

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1809
1810
1811
1812
1813
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Transportation FiberinMotion

Brand: Radwin Pages: 122

Brand: Lanner Pages: 2

Brand: Opvimus Pages: 12

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: RAIDAGE Pages: 60

Brand: Idis Pages: 16

Brand: ZIMO Pages: 13

SOUL CALIBUR II

Brand: NAMCO Pages: 26

Brand: IBM Pages: 74

Soundweb 9088ii DSP System

Brand: BSS Audio Pages: 2

SATA II-150 PCI

Brand: SIIG Pages: 16

Brand: ekwb Pages: 16

Homecraft Rolyan AA6240

Brand: Patterson Pages: 2

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brand: Omron Pages: 4

TeleLite 720920 Series

Brand: Positron Pages: 21

VDA-NVR2108W4KS2

Brand: Dahua Technology Pages: 363

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands