manualshive.com logo in svg

Texas Instruments MSA011, User Manual, Page: 7 / 15

Share
Download
Texas Instruments MSA011 User Manual Download Page 7

www.ti.com

EVM Connectors

7

SGLU009 – November 2016

Submit Documentation Feedback

Copyright © 2016, Texas Instruments Incorporated

TPS382-Q1EVM (MSA011) Voltage Supervisor with Watchdog Timer User

Guide

3.2

EVM Jumpers

Table 3

lists the jumpers onboard the TPS382-Q1EVM. As ordered, the TPS382-Q1EVM will have five

jumpers installed.

Table 3. List of Onboard Jumpers

Jumper

Device

Default Connection

Description

J2

TPS3820-33-Q1

VDD to MR

Connect MR to GND to force the device into
reset. Otherwise, connect MR to VDD or leave
MR floating.

J6

TPS3823-25-Q1

VDD to MR

Connect MR to GND to force the device into
reset. Otherwise, connect MR to VDD or leave
MR floating.

J14

TPS3825-50-Q1

VDD to MR

Connect MR to GND to force the device into
reset. Otherwise, connect MR to VDD or leave
MR floating.

J18

TPS3828-33-Q1

VDD to MR

Connect MR to GND to force the device into
reset. Otherwise, connect MR to VDD or leave
MR floating.

J19

TPS3828-33-Q2

Shorted

Enables the pullup to VDD for the open-drain
reset output. To use a different pullup voltage,
remove the shunt from J19 and supply a
different voltage to J19 pin 2.

3.3

EVM Input and Output Connectors

The following 2-pin headers are input and output connecters for each device.

Table 4. List of Input and Output Connectors

Jumper

Device

Description

J1

TPS3820-33-Q1

Supply voltage for TPS3820-33-Q1 and common ground.

J3

WDI pin for watchdog input. Leave floating if unused.

J4

Active low reset output.

J5

TPS3823-25-Q1

Supply voltage for TPS3823-25-Q1 and common ground.

J7

Active low reset output.

J8

WDI pin for watchdog. Leave floating if unused.

J9

TPS3824-30-Q1

Supply voltage for TPS3824-30-Q1 and common ground.

J10

WDI pin for watchdog. Leave floating if unused.

J11

Active low reset output.

J12

Active high reset output.

J13

TPS3825-50-Q1

Supply voltage for TPS3825-50-Q1 and common ground.

J15

Active low reset output.

J16

Active high reset output.

J17

TPS3828-33-Q1

Supply voltage for TPS3828-33-Q1 and common ground.

J20

WDI pin for watchdog input. Leave floating if unused.

J21

Active low reset output.

Summary of Contents for MSA011
















Reviews:

No comments