Texas Instruments Modular MSOP8 EVM User Manual Download Page 3 | Manualshive

Page: 3 / 20

Texas Instruments Modular MSOP8 EVM User Manual Download Page 3

-4

The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.

Related Documentation From Texas Instruments

To obtain a copy of any of the following TI documents, call the Texas
Instruments Literature Response Center at (800) 477−8924 or the Product
Information Center (PIC) at (972) 644−5580. When ordering, identify this
booklet by its title and literature number. Updated documents can also be
obtained through our website at www.ti.com.

EVM Compatible Device Data Sheets:

Literature Number:

ADS7816

SBAS110

ADS7817

SBAS230

ADS7818

SBAS078

ADS7822

SBAS062

ADS7834

SBAS098

ADS7835

SBAS102

ADS8317

SBAS356

ADS8320

SBAS108

ADS8321

SBAS123

ADS8324

SBAS172

ADS8325

SBAS226

ADS8326

SBAS343

Application Notes/Additional Literature:

Literature Number:

Op Amps for Everyone

SLOD006

5−6K Interface Board

SLAU104

Single and Bipolar Supply Signal Conditioning Boards

SLAU105

FCC Warning

This equipment is intended for use in a laboratory test environment only. It gen-
erates, uses, and can radiate radio frequency energy and has not been tested
for compliance with the limits of computing devices pursuant to subpart J of
part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other en-
vironments may cause interference with radio communications, in which case
the user at his own expense will be required to take whatever measures may
be required to correct this interference.

Downloaded from

electronic components distributor

«
1
2
3
4
5
...
»

Summary of Contents for Modular MSOP8 EVM





















Reviews:

No comments