background image

2 Introduction

The MCT8316A is a 4.5-V to 35-V, 8-A peak integrated three-phase gate driver IC with high speed 
sensorless trapezoidal control for motor drive applications. It provides three accurately trimmed and temperature 
compensated half-bridge MOSFETS, gate drivers, charge pump, current sense amplifier, linear regulator for the 
external load and adjustable buck regulator. The I2C interface variant (MCT8316A) also provides a standard I2C 
interface for configuring the various device settings and reading fault diagnostic information through an external 
controller.

The MCT8316AEVM includes an onboard FTDI chip to convert USB communication from the micro-USB 
connector into UART and an onboard MSP430FR2355 MCU to interface with the MCT8316A. It can also provide 
SPI communication for the SPI variant of the MCT8316A device. There are many user-selectable jumpers, 
resistors, connectors, and test points to evaluate many features of the device and configure device-specific 
settings.

This document serves as a startup guide to supplement the MCT8316AEVM. It is intended for engineers to 
design, implement, and validate reference hardware for the MCT8316A device.

Figure 2-1. MCT8316AEVM Printed Circuit Board (PCB - Top View)

www.ti.com

Introduction

SLLU340 – AUGUST 2021

Submit Document Feedback

MCT8316AEVM Evaluation Module

3

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for MCT8316AEVM























Reviews: