Texas Instruments LMX2594 User Manual Download Page 4 | Manualshive

Page: 4 / 32

Texas Instruments LMX2594 User Manual Download Page 4

Evaluation Board Setup

www.ti.com

4

SNAU210 – March 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

LMX2594 EVM Instructions – 15-GHz Wideband Low Noise PLL With
Integrated VCO

2

Evaluation Board Setup

Figure 2. LMX2594EVM Setup

SPACER

1. Power:

a. Set power supply to 3.3 V with 600-mA current limit and connect to V

CC

SMA.

2. Input Signal:

a. VC-708 100-MHz on-board oscillator enabled (default). To use another reference, see

Appendix D

.

3. Programming Interface:

•

Reference Pro will provide SPI interface to program LMX2594:

a. Connect USB cable from laptop or PC to USB port in Reference Pro. This provides power to

Reference Pro Board and communication with TICS GUI

b. Connect 10 pin ribbon cable from Reference Pro to LMX2594EVM as shown above.

4. Output:

a. Connect RFoutAM or RFoutAP to a phase noise Analyzer. Connect a 50-

Ω

on the unused output if

you are using only single-ended. Use a balun if you are using differential.

«
...
2
3
4
5
6
...
»

Summary of Contents for LMX2594

































Reviews:

No comments