manualshive.com logo in svg

Texas Instruments LDC3114, Manual

Share
Download
Texas Instruments LDC3114 Manual Download Page 21

Table 7-14. EN Register Field Descriptions

Bit

Field

Type

Reset

Description

7

LPEN3

R/W

0h

Channel 3 Low-Power-Enable

0h = Disable Channel 3 in Low Power Mode
1h = Enable Channel 3 in Low Power Mode. EN3 must also be set to 
1.

6

LPEN2

R/W

0h

Channel 2 Low-Power-Enable

0h = Disable Channel 2 in Low Power Mode
1h = Enable Channel 2 in Low Power Mode. EN2 must also be set to 
1.

5

LPEN1

R/W

0h

Channel 1 Low-Power-Enable

0h = Disable Channel 1 in Low Power Mode
1h = Enable Channel 1 in Low Power Mode. EN1 must also be set to 
1.

4

LPEN0

R/W

1h

Channel 0 Low-Power-Enable

0h = Disable Channel 0 in Low Power Mode
1h = Enable Channel 0 in Low Power Mode. EN0 must also be set to 
1.

3

EN3

R/W

1h

Channel 3 Enable

0h = Disable Channel 2
1h = Enable Channel 2

2

EN2

R/W

1h

Channel 2 Enable

0h = Disable Channel 2
1h = Enable Channel 2

1

EN1

R/W

1h

Channel 1 Enable

0h = Disable Channel 1
1h = Enable Channel 1

0

EN0

R/W

1h

Channel 0 Enable

0h = Disable Channel 0
1h = Enable Channel 0

7.5.1.13 NP_SCAN_RATE Register (Offset = Dh) [Reset = 01h] 

NP_SCAN_RATE is shown in 

NP_SCAN_RATE Register Field Descriptions

.

Return to the 

LDC3114 Registers

.

Normal Power Mode scan rate

Table 7-15. NP_SCAN_RATE Register Field Descriptions

Bit

Field

Type

Reset

Description

7-4

RESERVED

R/W

0h

Reserved

3

NPFSR

R/W

0h

Normal Power Mode Fast Scan Rate of 160SPS. When set, this bit 
will override setting in NPSR only and not NPCS.

2

NPCS

R/W

0h

Continuous key scan in Normal Power mode When set, the scan 
cycle is continuous without delay in the Normal Power mode. The 
base increment value is fixed. This bit has no effect if the chip is 
in Low Power mode. This bit will override the setting in NPSR and 
NPFSR registers.

www.ti.com

LDC3114

SNOSDD0 – DECEMBER 2021

Copyright © 2021 Texas Instruments Incorporated

Submit Document Feedback

21

Product Folder Links: 

LDC3114

Summary of Contents for LDC3114
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands