manualshive.com logo in svg

Texas Instruments INA220EVM, User Manual, Page: 21 / 26

Share
Download
Texas Instruments INA220EVM User Manual Download Page 21

www.ti.com

Revision History

21

SBOU079B – July 2009 – Revised May 2016

Submit Documentation Feedback

Copyright © 2009–2016, Texas Instruments Incorporated

Revision History

Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from A Revision (February 2010) to B Revision

.............................................................................................

Page

•

Changed

Figure 1

.........................................................................................................................

2

•

Changed list item From: "+6V power supply" To: "Barrel plug cable assembly..." in

Section 1.1

..............................

3

•

Added new paragraph and NOTE to

Section 2.3

.....................................................................................

7

•

Added "(on USB DIG board)" to J5 in

Table 3

.......................................................................................

12

•

Adddec "(on USB DIG board)" to J5 in

Table 4

.....................................................................................

13

Revision History

Changes from Original (July, 2009) to A Revision

..........................................................................................................

Page

•

Revised

Table 3

..........................................................................................................................

12

•

Added

Table 4

and

Table 5

............................................................................................................

13

•

Added

Section 3.7

.......................................................................................................................

14

•

Added

Section 3.8

.......................................................................................................................

14

Summary of Contents for INA220EVM



























Reviews:

No comments