Texas Instruments EMIF16 User Manual Download Page 57

Page: 57 / 63

4.24 NAND Flash Error Address 1 Register (NANDFEA1R)

SPRUGZ3A—May 2011

KeyStone Architecture External Memory Interface (EMIF16) User Guide

4-23

Submit Documentation Feedback

Chapter 4—Registers

www.ti.com

4.24 NAND Flash Error Address 1 Register (NANDFEA1R)

The NAND Flash Error Address 1 register is shown in

Figure 4-17

and described in

Table 4-18

Figure 4-17

NAND Flash Error Address 1 Register (NANDFEA1R)

Reserved

ERR_ADDR2

Reserved

ERR_ADDR1

R - 0x0

Table 4-18

NAND Flash Error Address 1 Register (NANDFEA1R) Details

Bit

Field

Value

Description

31-26

Reserved

0x0

Reserved. The reserved bit location is always read as 0. A value written to this field has no effect

25-16

ERR_ADDR2

0x0

4-Bit error address 2.

15-10

Reserved

0x0

Reserved. The reserved bit location is always read as 0. A value written to this field has no effect

9-0

ERR_ADDR1

0x0

4-Bit error address 1.

End of Table 4-18

Summary of Contents for EMIF16
































































Search results

Summary of Contents for EMIF16

Reviews:

Brands by name

Popular brands

Texas Instruments EMIF16, User Manual

Search results

Summary of Contents for EMIF16

Reviews:

Brands by name

Popular brands