Hardware Description
www.ti.com
6
SLLU224B – August 2015 – Revised March 2018
Submit Documentation Feedback
Copyright © 2015–2018, Texas Instruments Incorporated
DP159RSB Evaluation Module
2.5
Component Population Configuration
To allow the DP159RSBEVM to support both the default DP input as well as a HDMI test input, there are
many components that need to be removed, placed, or modified depending on the board configuration.
Here’s a summary of the default component configuration for the DP159RSBEVM. In addition, the unused
HDMI receptacle is depopulated.
Function
Reference Designator
DP159RSBEVM
Differential Pair - IN
C11, C12, C13, C14, C15, C16, C24,
C25
populated with 0.1 µF
Differential Pair - HDMI IN
R14, R15, R18, R19, R20, R21, R22,
R23
not populated
SDA / SCL - HDMI
R16, R17, R24, R25, R134, R135
not populated
Differential Pair - DP IN
R112, R109, R111, R108, R110, R107,
R106, R105
populated with 0
Ω
SDA / SCL / HPD - DP
R33, R31, R32 (R126, R136, R140,
R141 - snoop)
populated with 0
Ω
Pullup Differential Pair HDMI IN
R1, R2, R3, R4, R6, R7, R8, R9
populated, but not
connected
2.5.1
HPD Snoop Option
To accommodate systems that do not properly resend DDC commands after HPD goes low, we have
implemented a HPD snoop mode on the DP159RSBEVM. This mode allows the HPD line to be routed
around the DP159, but remain connected to the DP159 on the sink side to allow the DP159 to snoop its
state. This snoop mode is disabled by default on the DP159RSBEVMs.
•
Pop R131, no pop R129, R130, R139 for HPD on
•
No pop R131, pop R129, R130, R139 for HPD snoop only
2.5.2
DDC Snoop Option – not Available for DP159RSB REV B
To accommodate systems that do not properly support clock stretching on the DDC lines, we have
implemented a snoop mode on the DP159RSBEVM. This mode allows the DDC lines to be routed around
the DP159RSB, but remain connected to the DP159RSB on the sink side to allow the DP159RSB to
snoop the DDC traffic. This snoop mode is disabled by default on the DP159RSB REV B1 EVMs.
•
Pop R126, R136, R140, R141. No pop R31, R32 – DP159RSB, DDC snoop only
•
Pop R31, R32. No pop R126, R136, R140, R141- DP159RSB, DDC on
2.6
Local I
2
C Access Through J5
Access to DP159’s local I
2
C signals is provided via the J5 input connector. Note that I
2
C signal levels
should be at 3.3 V when I
2
C interface is accessed through the connector.
A standalone external I
2
C host can be connected via J5 for debug and control purposes. An example of an
external I
2
C Host controller is the Total Phase Aardvark™ I
2
C/SPI Host Adapter (Total Phase Part#:
TP240141
). Sample scripts for this I
2
C Host controller are provided by request.
Table 2. Aardvark I
2
C (J5) Pin-Out
J5 pin #
Description
J5 pin
#
Description
1
SCL_CTL
2
GND
3
SDA_CTL
4
NC
5
NC
6
NC
7
NC
8
NC
9
NC
10
GND