Texas Instruments DLPDLCR660TEVM User Manual Download Page 5 | Manualshive

Page: 5 / 34

background image

5

DLPU077 – March 2019

Submit Documentation Feedback

Copyright © 2019, Texas Instruments Incorporated

Read This First

Preface

DLPU077 – March 2019

Read This First

Trademarks

DLP is a registered trademark of Texas Instruments.

About This Guide

This guide explains the hardware and software features of the DLP Products DLPDLCR660TEVM and
DLPLCRDC4422EVM systems. The EVM architecture and connectors will be described along with a quick
start guide on how to operate the DLPDLCR660TEVM and DLPLCRDC4422EVM EVMs using the
DLPC4422 GUI. Specific DLP

®

chip details and operation can be found in related component

documentation.

NOTE:

Power supply, optics, illumination source, and cables are sold separately. See

Needed for Operation

Figure 1. DLP DLPDLCR660TEVM and DLPLCRDC4422EVM Evaluation Module

Related Documentation from Texas Instruments

DLP660TE Data Sheet: DLP660TE Digital Micromirror Device (DMD),

DLPC4422 Data Sheet: DLPC4422 DLP Display Controller,

DLPA100 Data Sheet: DLPA100 Power Management and Motor Driver,

TPS65145 Data Sheet: TPS65145 Triple Output LCD Supply with Linear Regulator and Power,

«
...
3
4
5
6
7
...
»

Summary of Contents for DLPDLCR660TEVM



































Reviews:

No comments

Related manuals for DLPDLCR660TEVM

Brand: jbc Pages: 4

Brand: Waterway Pages: 16

Brand: Gardena Pages: 14

Brand: Gardena Pages: 8

Brand: IBM Pages: 276

Brand: IBM Pages: 32

Brand: IBM Pages: 157

Brand: Xilinx Pages: 2

Brand: Paser Pages: 2

Brand: Computer Automation Technology Pages: 55

Brand: Pfeiffer Vacuum Pages: 100

Brand: D+H Pages: 36

Brand: netvox Pages: 12

Brand: CAME Pages: 128

Comfort System Z-300-HC

Brand: Jackson Systems Pages: 2

GA Industries FIGURE 927

Brand: Vag Pages: 5

Brand: C&K systems Pages: 4

SatService sat-nms VLC

Brand: Calian Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands