background image

www.ti.com

Safety Instructions

3

DLPU058 – September 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

DLP

®

LightCrafter™ Display 3010 EVM Gen2 User's Guide

2

Safety Instructions

CAUTION

Caution hot surface. Contact may cause burns. Do not touch.

WARNING

Possible hazardous optical radiation emitted from this product. Do
not stare at the operating lamp. May be harmful to the eye.

WARNING

Observe handling precautions. Electrostatic sensitive devices.

WARNING

Always ensure both fans are running during operation to avoid
overheating and ensure reliable operation.

3

Applicable Documents

The following documents are applicable to the DLP LightCrafter Display 3010 EVM and are available at
TI.com (

www.ti.com

).

DLP3010 (0.3 720p) digital micromirror device (DMD) data sheet (

DLPS051

)

DLPA3000 controller data sheet (

DLPS052

)

DLPC3433 controller data sheet (

DLPS035

)

DLPC3433 Software Programmer's Guide (

DLPU020

)

DLP LightCrafter Display EVM GUI Tool User's Guide (

DLPU021

)

If you need assistance, refer to the

DLP Products and MEMS TI E2E™ community support forums.

Summary of Contents for DLP LightCrafter 3010 Gen2












Reviews: