manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Technical Reference Manual

The Texas Instruments Concerto F28M35 Series is a powerful microcontroller designed for high-performance applications. With its comprehensive Technical Reference Manual available for free download from our website, users can easily access detailed information and instructions to maximize the product's capabilities. Enhance your project with the Concerto F28M35 Series today.

Share
Download
background image

General-Purpose Input/Output (GPIO)

www.ti.com

356

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

General-Purpose Input/Output (GPIO)

4.1.6.14 GPIO Lock (GPIOLOCK) Register, offset 0x520

The GPIOLOCK register enables write access to the GPIOCR register. Writing 0x4C4F.434B to the
GPIOLOCK register unlocks the GPIOCR register. Writing any other value to the GPIOLOCK register re-
enables the locked state. Reading the GPIOLOCK register returns the lock status rather than the 32-bit
value that was previously written. Therefore, when write accesses are disabled, or locked, reading the
GPIOLOCK register returns 0x0000.0001. When write accesses are enabled, or unlocked, reading the
GPIOLOCK register returns 0x0000.0000.

Figure 4-17. GPIO Lock (GPIOLOCK) Register

31

16

LOCK

R/W-0

15

0

LOCK

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 4-19. GPIO Lock (GPIOLOCK) Register Field Descriptions

Bit

Field

Value

Description

31-0

LOCK

GPIO Lock

A write of the value 0x4C4F.434B unlocks the GPIO Commit (GPIOCR) register for write access. A
write of any other value or a write to the GPIOCR register reapplies the lock, preventing any
register updates. A read of this register returns the following values:

0

The GPIOCR register is unlocked and may be modified.

1

The GPIOCR register is locked and may not be modified.

4.1.6.15 GPIO Commit (GPIOCR) Register, offset 0x524

The GPIOCR register is the commit register. The value of the GPIOCR register determines which bits of
the GPIOAFSEL, GPIOPUR, GPIOCSEL, and GPIODEN registers are committed when a write to these
registers is performed. If a bit in the GPIOCR register is cleared, the data being written to the
corresponding bit in the GPIOAFSEL, GPIOPUR, GPIOCSEL, or GPIODEN registers cannot be
committed and retains its previous value. If a bit in the GPIOCR register is set, the data being written to
the corresponding bit of the GPIOAFSEL, GPIOPUR, GPIOCSEL, or GPIODEN registers is committed to
the register and reflects the new value.

The contents of the GPIOCR register can only be modified if the status in the GPIOLOCK register is
unlocked. Writes to the GPIOCR register are ignored if the status in the GPIOLOCK register is locked.

Important:

This register is designed to prevent accidental programming of the registers that control

connectivity to the NMI hardware. By initializing the bit of the GPIOCR register to 0 for PB7, the NMI can
only be converted to a GPIO through a deliberate set of writes to the GPIOLOCK, GPIOCR, and the
corresponding registers.

Because this protection is currently only implemented on the NMI pin on PB7, all of the other bits in the
GPIOCR registers cannot be written with 0x0. These bits are hardwired to 0x1, ensuring that it is always
possible to commit new values to the GPIOAFSEL, GPIOPUR, GPIOCSEL, or GPIODEN register bits of
these other pins.

Summary of Contents for Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Concerto F28M35 Series

Ubisys J1 Manual preview
J1
Brand: Ubisys Pages: 2
Panasonic FP0 Series Specifications preview
FP0 Series
Brand: Panasonic Pages: 27
Panasonic CZ-64ESMC2 Instruction Manual preview
CZ-64ESMC2
Brand: Panasonic Pages: 78
Panasonic GM1 Series Reference Manual preview
GM1 Series
Brand: Panasonic Pages: 98
NAiS FP0 Series Hardware Manual preview
FP0 Series
Brand: NAiS Pages: 173
Panasonic SL-VGU1-EC Instruction Manual preview
SL-VGU1-EC
Brand: Panasonic Pages: 2
Barthelme CHROMOFLEX RC Instruction Manual preview
CHROMOFLEX RC
Brand: Barthelme Pages: 8
Daikin ALTHERMA User Manual preview
ALTHERMA
Brand: Daikin Pages: 5
H3C WX Series Configuration Manual preview
WX Series
Brand: H3C Pages: 69
J+J J4C Series Installation Instructions preview
J4C Series
Brand: J+J Pages: 2
DeLaval MPCII Memo preview
MPCII
Brand: DeLaval Pages: 102
2N 9160341 Installation Manual preview
9160341
Brand: 2N Pages: 107
Allen-Bradley Micro850 series Installation Instructions Manual preview
Micro850 series
Brand: Allen-Bradley Pages: 24
Hoffer 214D-1 User Manual preview
214D-1
Brand: Hoffer Pages: 57
Samson TROVIS 5571 Mounting And Operating Instructions preview
TROVIS 5571
Brand: Samson Pages: 44
Beckhoff C6925 Manual preview
C6925
Brand: Beckhoff Pages: 47
DOTECH FX3DH Series Manual preview
FX3DH Series
Brand: DOTECH Pages: 4
MISUMI DS102MS Operation Manual preview
DS102MS
Brand: MISUMI Pages: 166

Brands by name

Popular brands

Load more brands