December 2013
CC2500EMK Quick Start Guide
Opening the box and using the modules with SmartRF04EB
1. Kit Contents
2 x CC2500 Evaluation Modules
2 x Antennas (Pulse W1010, 2 dBi) *
Documentation
The RF boards in this kit are FCC and IC certified
and they are tested to comply with ETSI/R&TTE
over temperatures from 0 to +35°C.
FCC/IC Regulatory Compliance
FCC Part 15 Class A Compliant
IC ICES-003 Class A Compliant
(*) Picture may deviate!
2. How to use the modules
The CC2500EM boards can be plugged into
several
development
boards
from
Texas
Instruments. Most notably, you can use the
SmartRF04EB,
which
is
included
in
the
CC2500DK. This board lets you run a packet
error rate (PER) test, control the device from
SmartRF™ Studio and it can be used as a
development platform.
The board can also be plugged into the SmartRF
TrxEB
(included
in
e.g.
CC1120DK
and
CC1200DK) and the MSP430 Expe
rimenter’s
Boards.
For prototyping with other microcontrollers, plug
the EM into the “SoC Battery Board”
(
).
This guide will show how to use the modules
together with SmartRF04EB.
3. Plug EM into SmartRF04EB
Insert a CC2500EM (EM) with an antenna into
the SmartRF04EB (EB). Connect the antenna
firmly to the SMA connector on the EM.
Caution!
The
kit
contains
ESD
sensitive components. Handle with care
to prevent permanent damage.
4a. Power: Battery
There are three different ways of applying power
to the EB:
The first method involves using an alkaline non-
rechargeable battery, either a 9V or a 4xAA
battery pack connected to the battery connector
on the bottom side of the board
Warning!
To minimize risk of personal injury or
property damage, ONLY use alkaline non-
rechargeable batteries. Never use rechargeable
batteries to power the board.
4b. Power: DC/External
The second method applies DC power using
the DC input jack (right in picture, centre is +,
sleeve is ground), or by connecting a 4-10V
voltage source between the 4-10V and 0V
terminals of the power connector (left in
picture). It is also possible to connect a 3.3V
voltage source between the 3.3V and 0V
terminals. The on-board voltage regulators will
be bypassed in this case.
External Power Supply
1
Requirements:
Nom Voltage: 6 VDC
Max Current: 800 mA
Efficiency Level V
4c. Power: USB
The EB can also be powered from the USB bus.
Make sure that the SmartRF
™ Studio software is
installed before connecting the EB to the PC;
otherwise you may experience problems in
installing it later due to driver issues.
Note that if multiple power sources are
connected, the source with the highest voltage
will power the EB.
This means that you should
disconnect any attached battery when using a
lab supply or USB power; otherwise the
battery will be drained.
5. Set Power Switch
If a 3.3V source is used as described in 4b
above, the switch should be set to the leftmost
position. For all other cases, the switch should
be set to the rightmost position. This switch can
be used to turn off the EB by switching it to the
opposite position of that used to turn it on
Do not leave the board powered when
unattended.
6. Packet Error Rate Test
When power is applied to the board, the PER test
program will start. You should see the text shown
above on the LCD display on both evaluation
boards.
Press the button marked S1 (lower right corner)
to continue.
7. Set Frequency Band
Select the desired frequency band of operation by
using the joystick. The frequency should match
the evaluation module and antenna you are
using.
Note that the value shown in the display is also
the selected value. There is no need to press a
button to select or activate the selection.
1
When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional product regulatory and
safety certification requirements such as UL, CSA, VDE, CCC, and PSE
