manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 903

www.ti.com

Registers

903

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

External Memory Interface A (EMIFA)

19.4.4 SDRAM Refresh Control Register (SDRCR)

The SDRAM refresh control register (SDRCR) is used to configure the rate at which connected SDRAM
devices will be automatically refreshed by the EMIFA. Refer to

Section 19.2.4.6

on the refresh controller

for more details. The SDRCR is shown in

Figure 19-34

and described in

Table 19-52

.

Figure 19-34. SDRAM Refresh Control Register (SDRCR)

31

16

Reserved

R-0

15

13

12

0

Reserved

RR

R-0

R/W-4E2h

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 19-52. SDRAM Refresh Control Register (SDRCR) Field Descriptions

Bit

Field

Value

Description

31-16

Reserved

0

Reserved. The reserved bit location is always read as 0. If writing to this field, always write the
default value of 0.

12-0

RR

0-1FFFh

Refresh Rate. This field is used to define the SDRAM refresh period in terms of EMA_CLK cycles.
Writing a value < 0x0020 to this field will cause it to be loaded with (2 × T_RFC) + 1 value from the
SDRAM timing register (SDTIMR).

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands