manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 899

www.ti.com

Registers

899

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

External Memory Interface A (EMIFA)

19.4.1 Module ID Register (MIDR)

This is a read-only register indicating the module ID of the EMIFA. The MIDR is shown in

Figure 19-31

and described in

Table 19-49

.

Figure 19-31. Module ID Register (MIDR)

31

0

REV

R-4000 0205h

LEGEND: R = Read only; -

n

= value after reset

Table 19-49. Module ID Register (MIDR) Field Descriptions

Bit

Field

Value

Description

31-0

REV

4000 0205h

Module ID of EMIFA.

19.4.2 Asynchronous Wait Cycle Configuration Register (AWCC)

The asynchronous wait cycle configuration register (AWCC) is used to configure the parameters for
extended wait cycles. Both the polarity of the EMA_WAIT pin(s) and the maximum allowable number of
extended wait cycles can be configured. The AWCC is shown in

Figure 19-32

and described in

Table 19-50

. Not all devices support both EMA_WAIT[1] and EMA_WAIT[0], see the device-specific data

manual to determine support on each device.

NOTE:

The EW bit in the asynchronous

n

configuration register (CE

n

CFG) must be set to allow for

the insertion of extended wait cycles.

Figure 19-32. Asynchronous Wait Cycle Configuration Register (AWCCR)

31

30

29

28

27

24

23

22

21

20

19

18

17

16

Reserved

WP1

WP0

Reserved

CS5_WAIT

CS4_WAIT

CS3_WAIT

CS2_WAIT

R-0

R/W-1

R/W-1

R-0

R/W-0

R/W-0

R/W-0

R/W-0

15

8

7

0

Reserved

MAX_EXT_WAIT

R-0

R/W-80h

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands