manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 851

EMA_WE_DQM[1:0]

DQ[15:0]

asynchronous

BE[1:0]

EMA_WE

EMA_D[15:0]

EMA_CS[n]

EMIFA

WE

CE

device

16−bit

EMA_D[7:0]

EMA_A[x:0]

EMA_BA[1:0]

DQ[7:0]

A[(x+2):2]
A[1:0]

EMIFA

8−bit

asynchronous

memory

a) EMIF to 8-bit memory interface

EMA_D[15:0]

EMA_A[x:0]

EMA_BA[1]

DQ[15:0]

A[(x+1):1]

A[0]

EMIFA

16−bit asynchronous

memory

b) EMIF to 16-bit memory interface

www.ti.com

Architecture

851

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

External Memory Interface A (EMIFA)

Of special note is the connection between the EMIFA and the external device's address bus. The EMIFA
address pin EMA_A[0] always provides the least significant bit of a 32-bit word address. Therefore, when
interfacing to a 16-bit or 8-bit asynchronous device, the EMA_BA[1] and EMA_BA[0] pins provide the
least-significant bits of the halfword or byte address, respectively. Additionally, when the EMIFA interfaces
to a 16-bit asynchronous device, the EMA_BA[0] pin can serve as the upper address line EMA_A[22].
Note that the width of the address bus varies with devices; therefore, see your device-specific data
manual for the EMA_A bus width supported.

Figure 19-8

and

Figure 19-9

show the mapping between the

EMIFA and the connected device's data and address pins for various programmed data bus widths. The
data bus width may be configured in the asynchronous

n

configuration register (CE

n

CFG).

Figure 19-9

shows a common interface between the EMIFA and external asynchronous memory.

Figure 19-9

shows an interface between the EMIFA and an external memory with byte enables. The

EMIFA should be operated in either Normal Mode or Select Strobe Mode when using this interface, so
that the EMA_WE_DQM signals operate as byte enables.

Figure 19-8. EMIFA to 8-bit/16-bit Memory Interface

Figure 19-9. Common Asynchronous Interface

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands