manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 296

AINTC Registers

www.ti.com

296

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

ARM Interrupt Controller (AINTC)

11.4.9 Host Interrupt Enable Indexed Set Register (HIEISR)

The host interrupt enable indexed set register (HIEISR) allows enabling a host interrupt output. The host
interrupt to enable is the INDEX value written. This enables the host interrupt output or triggers the output
again if already enabled. The HEISR is shown in

Figure 11-11

and described in

Table 11-11

.

Figure 11-11. Host Interrupt Enable Indexed Set Register (HEISR)

31

16

Reserved

R-0

15

1

0

Reserved

INDEX

R-0

W-0

LEGEND: R = Read only; W = Write only; -

n

= value after reset

Table 11-11. Host Interrupt Enable Indexed Set Register (HEISR) Field Descriptions

Bit

Field

Value

Description

31-1

Reserved

0

Reserved

0

INDEX

Writes set the enable of the host interrupt given in the INDEX value. Reads return 0.

0

Writing a 0 sets FIQ.

1

Writing a 1 sets IRQ.

11.4.10 Host Interrupt Enable Indexed Clear Register (HIEICR)

The host interrupt enable indexed clear register (HIEICR) allows disabling a host interrupt output. The host
interrupt to disable is the INDEX value written. This disables the host interrupt output. The HIEICR is
shown in

Figure 11-12

and described in

Table 11-12

.

Figure 11-12. Host Interrupt Enable Indexed Clear Register (HIEICR)

31

16

Reserved

R-0

15

1

0

Reserved

INDEX

R-0

W-0

LEGEND: R = Read only; W = Write only; -

n

= value after reset

Table 11-12. Host Interrupt Enable Indexed Clear Register (HIEICR) Field Descriptions

Bit

Field

Value

Description

31-1

Reserved

0

Reserved

0

INDEX

Writes clear the enable of the host interrupt given in the INDEX value. Reads return 0.

0

Writing a 0 clears FIQ.

1

Writing a 1 clears IRQ.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands