manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 1752

Registers

www.ti.com

1752

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Universal Serial Bus 2.0 (USB) Controller

34.4.84 Queue Manager Queue Pending Register 0 (PEND0)

The queue pending register 0 (PEND0) can be read to find the pending status for queues 31 to 0. It does
not support byte accesses. The queue pending register 0 (PEND0) is shown in

Figure 34-110

and

described in

Table 34-114

.

NOTE:

The pending bit gets set when a Descriptor address is loaded in a Queue. The loading action

causes the corresponding bit for that Queue to get set. Similarly, the pending bit gets cleared
when the Descriptor address is off-loaded from a Queue by reading it. One way to check if
the receive or transmit transfer has completed is by checking the bit that corresponds to the
desired Completion Queue for that particular transfer. When the Queue Manager is finished
with the transfer, it will load the Descriptor address to the Completion Queue.

Figure 34-110. Queue Manager Queue Pending Register 0 (PEND0)

31

0

QPEND0

R-0

LEGEND: R = Read only; -

n

= value after reset

Table 34-114. Queue Manager Queue Pending Register 0 (PEND0) Field Descriptions

Bit

Field

Value

Description

31-0

QPEND0

0-FFFF FFFFh

This field indicates the queue pending status for queues 31-0.

34.4.85 Queue Manager Queue Pending Register 1 (PEND1)

The queue pending register 1 (PEND1) can be read to find the pending status for queues 63 to 32. It does
not support byte accesses. The queue pending register 1 (PEND1) is shown in

Figure 34-111

and

described in

Table 34-115

.

NOTE:

The pending bit gets set when a Descriptor address is loaded in a Queue. The loading action

causes the corresponding bit for that Queue to get set. Similarly, the pending bit gets cleared
when the Descriptor address is off-loaded from a Queue by reading it. One way to check if
the receive or transmit transfer has completed is by checking the bit that corresponds to the
desired Completion Queue for that particular transfer. When the Queue Manager is finished
with the transfer, it will load the Descriptor address to the Completion Queue.

Figure 34-111. Queue Manager Queue Pending Register 1 (PEND1)

31

0

QPEND1

R-0

LEGEND: R = Read only; -

n

= value after reset

Table 34-115. Queue Manager Queue Pending Register 1 (PEND1) Field Descriptions

Bit

Field

Value

Description

31-0

QPEND1

0-FFFF FFFFh

This field indicates the queue pending status for queues 63-32.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands