manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

The Texas Instruments AM1808 User Manual is a comprehensive guide designed to assist users in getting the most out of their AM1808 product. This manual provides step-by-step instructions, troubleshooting tips, and detailed information about the device's features and functionalities. Download your free copy exclusively from manualshive.com today.

Share
Download
background image

uPP

I/O Channel A

DMA Channel I

Memory

DMA Channel Q

DATA pins

uPP

I/O Channel A

DMA Channel I

Memory

I/O Channel B

DMA Channel Q

Data pins

Data pins

www.ti.com

Introduction

1537

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Universal Parallel Port (uPP)

Figure 32-4. Data Flow for Digital Loopback (DLB) Mode (Duplex Mode 0)

Figure 32-5. Data Flow for Single-Channel Transmit with Data Interleave

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AM1808

IBM 3270 Operation Manual preview
3270
Brand: IBM Pages: 86
3Com 3CRWB6096 Quick Start Manual preview
3CRWB6096
Brand: 3Com Pages: 8
Dentsply Sirona inLab Speedcure 9494800 Instruction Manual preview
inLab Speedcure 9494800
Brand: Dentsply Sirona Pages: 91
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Brand: ETL Pages: 83
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Brand: Loopcomm Pages: 2
S&T Kontron SMARC-sXEL User Manual preview
Kontron SMARC-sXEL
Brand: S&T Pages: 108
B&B Electronics 232PCC User Manual preview
232PCC
Brand: B&B Electronics Pages: 17
MA lighting 8Port Node Quick Manual preview
8Port Node
Brand: MA lighting Pages: 49
COUGAR Vortex SPB 120 User Manual preview
Vortex SPB 120
Brand: COUGAR Pages: 2
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
ICP DAS USA VEX-112 Quick Start Manual preview
VEX-112
Brand: ICP DAS USA Pages: 8
IBA ibaBM-FOX-i-3o-D Manual preview
ibaBM-FOX-i-3o-D
Brand: IBA Pages: 13
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
Westlock Controls Corporation Intellis 7604 Installation And Operation Manual preview
Intellis 7604
Brand: Westlock Controls Corporation Pages: 39
WEIGL Nanotec Instruction Manual preview
Nanotec
Brand: WEIGL Pages: 6
Icop VMXP-6453 User Manual preview
VMXP-6453
Brand: Icop Pages: 31
A.E.B. 628450000 Assembly & Instruction Manual preview
628450000
Brand: A.E.B. Pages: 10

Brands by name

Popular brands

Load more brands