manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 1377

www.ti.com

Registers

1377

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Serial ATA (SATA) Controller

28.4.3 Interrupt Status Register (IS)

The interrupt status register (IS) indicates which port inside of the subsystem has a pending interrupt. The
IS is shown in

Figure 28-3

and described in

Table 28-7

.

Figure 28-3. Interrupt Status Register (IS)

31

16

Reserved

R-0

15

2

1

0

Reserved

IPS[

n

]

R-0

R/W1C-0

LEGEND: R/W = Read/Write; R = Read only; W1C = Write 1 to clear; -

n

= value after reset

Table 28-7. Interrupt Status Register (IS) Field Descriptions

Bit

Field

Value

Description

31-2

Reserved

0

Reserved.

1-0

IPS[

n

]

0-1

Interrupt Pending Status. If a bit

n

is set to 1 If set, the corresponding Port has an interrupt pending.

Software can use this information to determine which Ports require service after an interrupt. The bits of
this field are set by the Ports that have interrupt events pending in the port interrupt status register
(P0IS) bits and enabled by the port interrupt enable register (P0IE) bits. Set bits are cleared by the
software writing 1 to all bits to clear.

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands