manualshive.com logo in svg

Texas Instruments AM1802, Reference Manual

Share
Download
Texas Instruments AM1802 Reference Manual Download Page 234

AINTC Registers

www.ti.com

11.4.15 Global Prioritized Vector Register (GPVR)

The global prioritized vector register (GPVR) shows the interrupt vector address of the highest priority
interrupt pending across all the host interrupts. The GPVR is shown in

Figure 11-17

and described in

Table 11-17

.

Figure 11-17. Global Prioritized Vector Register (GPVR)

31

0

ADDR

R-0

LEGEND: R = Read only; -n = value after reset

Table 11-17. Global Prioritized Vector Register (GPVR) Field Descriptions

Bit

Field

Value

Description

31-0

ADDR

0-FFFF FFFFh

The currently highest priority interrupts vector address across all the host interrupts.

11.4.16 System Interrupt Status Raw/Set Register 1 (SRSR1)

The system interrupt status raw/set register 1 (SRSR1) shows the pending enabled status of the system
interrupts 0 to 31. Software can write to SRSR1 to set a system interrupt without a hardware trigger. There
is one bit per system interrupt. The SRSR1 is shown in

Figure 11-18

and described in

Table 11-18

.

Figure 11-18. System Interrupt Status Raw/Set Register 1 (SRSR1)

31

0

RAW_STATUS[n]

W-0

LEGEND: W = Write only; -n = value after reset

Table 11-18. System Interrupt Status Raw/Set Register 1 (SRSR1) Field Descriptions

Bit

Field

Value

Description

31-0

RAW_STATUS[n]

System interrupt raw status and setting of the system interrupts 0 to 31. Reads return the raw
status.

0

Writing a 0 has no effect.

1

Write a 1 in bit position [n] to set the status of the system interrupt n.

234

ARM Interrupt Controller (AINTC)

SPRUGX5A

–

May 2011

Submit Documentation Feedback

Copyright

©

2011, Texas Instruments Incorporated

Summary of Contents for AM1802



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands