background image

www.ti.com

ADS8638EVM-PDK Kit Operation

6.3

Connecting the Power Supply

The ADS8638EVM-PDK requires multiple supplies to power the ADC to be used with the MMB0
motherboard. The ADS8638 requires two high-voltage supplies (

±

10 V to

±

15 V), HVDD and HVEE, along

with a +5-V supply to power the analog, AVDD, and +3.3 V to +5 V to power the digital circuitry, DVDD.

When the MMB0 DSP is powered properly, LED D2 glows green. The green light indicates that the 3.3-V
supply for the MMB0 is operating properly. (It does not indicate that the EVM power supplies are
operating properly.)

6.3.1

Connecting the Laboratory Power Supply

A laboratory power supply can be connected through terminal block J14 on the MMB0, as shown in

Figure 6

. To use a unipolar lab power supply configuration, follow these procedures:

Disconnect J12 on the MMB0.

Connect a +5-V dc supply to the +5 VD terminal on J14.

Connect ground of the dc supply to the GND terminal on J14.

For bipolar mode, also connect a

10-V dc supply to the

VA, and +10 V on the +VA terminals on J14.

It is not necessary to connect a +5-V dc supply voltage to the +5 VA terminal on J14 if the +5 V/+5 VA
position on J13 is shorted.

Figure 6. Laboratory Power-Supply Connections

11

SBAU192

July 2011

ADS8638EVM-PDK

Submit Documentation Feedback

Copyright

©

2011, Texas Instruments Incorporated

Summary of Contents for ADS8638EVM-PDK



























Reviews: