Texas Instruments ADS54J64 User Manual Download

Page: 1 / 24

SBAU290 – September 2017

ADS54J64 Evaluation Module

User's Guide

SBAU290 – September 2017

ADS54J64 Evaluation Module

The ADS54J64EVM device is an evaluation board used to evaluate the ADS54J64 Integrated Receiver
from TI. This user’s guide is intended to guide users through setting up and evaluating the ADC for the
best performance.

Contents

Overview

......................................................................................................................

1.1

Required Hardware

.................................................................................................

1.2

Required Software

..................................................................................................

1.3

Evaluation Board Feature Identification Summary

.............................................................

1.4

References

..........................................................................................................

Quick Start Guide

............................................................................................................

2.1

Software Installation

................................................................................................

2.2

Hardware Setup Procedure

.......................................................................................

2.3

Software Setup Procedure

.........................................................................................

2.4

Quick Start Troubleshooting

.......................................................................................

Optimizing Evaluation Results

............................................................................................

3.1

ADS54J64 Operating Mode

......................................................................................

3.2

LMK04828 Clocking Configuration

..............................................................................

3.3

Using an External Clock

..........................................................................................

3.4

Using a Coherent Input Source Frequency

....................................................................

3.5

HSDC Pro Settings

................................................................................................

Software Description

.......................................................................................................

4.1

ADS54J64 GUI

....................................................................................................

4.2

Low Level View

....................................................................................................

EVM Hardware Modifications from Default

.............................................................................

Appendix A

.......................................................................................................................

List of Figures

EVM Feature Locations

.....................................................................................................

Quick Start Test Setup

......................................................................................................

HSDC Pro GUI Main Panel

.................................................................................................

HSDC Pro Sampling Rate and Additional Device Parameters

........................................................

Data Capture Results From Quick Start Procedure

.....................................................................

Test Setup Using an External Device Clock Source

..................................................................

ADS54J64 GUI

.............................................................................................................

Low Level View Tab

.......................................................................................................

List of Tables

Quick Start Performance Measurements

.................................................................................

Troubleshooting Tips

........................................................................................................

HSDC Pro ADC Output Data Rate

......................................................................................

LK04828 Macro States Provided in Configuration GUI

...............................................................

HSDC Pro Options for Optimal Analysis Results

......................................................................

ADS54J64 GUI Tab Descriptions

........................................................................................

Summary of Contents for ADS54J64

























Search results

Summary of Contents for ADS54J64

Reviews:

Related manuals for ADS54J64

Brands by name

Popular brands

Texas Instruments ADS54J64, User Manual

Search results

Summary of Contents for ADS54J64

Reviews:

Related manuals for ADS54J64

Brands by name

Popular brands