manualshive.com logo in svg

Texas Instruments ADS1147EVM, User Manual

Share
Download
Texas Instruments ADS1147EVM User Manual Download Page 8

ADS1247EVM-PDK Kit Operation

www.ti.com

7.3

Default Jumper Settings and Switch Positions

Figure 3

shows the jumpers found on the EVM and the respective factory default conditions for each.

Figure 3. ADS1247EVM Default Jumper Locations

Table 6

lists the switches found on the EVM and the respective factory default conditions for each.

Table 6. List of Switches

Switch

Default Position

Switch Description

S1

Left

Onboard reference

8

ADS1247EVM-PDK Kit Operation

This section provides information on using the ADS1247EVM-PDK, including setup, program installation,
and program usage.

To prepare to evaluate the ADS1247 with the ADS1247EVM-PDK, complete the following steps:

Step 1.

Install the ADCPro software (if not already installed) on a PC.

Step 2.

Install the ADS1247EVM-PDK EVM plug-in software.

Step 3.

Complete the USB driver installation process.

Step 4.

Set up the ADS1247EVM-PDK.

Step 5.

Connect the ADS1247EVM-PDK to the computer with a USB cable.

Step 6.

Run the ADCPro software.

Each task is described in the subsequent sections of this document.

8

ADS1147EVM, ADS1247EVM, ADS1147EVM-PDK, ADS1247EVM-PDK

SBAU148B

–

June 2009

–

Revised May 2011

Submit Documentation Feedback

Copyright

©

2009

–

2011, Texas Instruments Incorporated

Summary of Contents for ADS1147EVM


































Reviews:

No comments

Brands by name

Popular brands

Load more brands