background image

User's Guide

SBAU203 – July 2013

ADS1x20EVM

ADS1x20EVM

This user's guide describes the characteristics, operation, and use of the ADS1x20EVM. These evaluation
modules are an evaluation system for the

ADS1220

, a 24-bit, low-power, multichannel, delta-sigma (

ΔΣ

),

analog-to-digital converter (ADC) and the

ADS1120

, which is the 16-bit version of the ADS1220. The EVM

allows evaluation of all aspects of the ADS1x20 devices.

This document includes an EVM Quick Start, hardware and software details, bill of materials, and
schematic.

Table 1

lists the related documents available through the Texas Instruments web site at

www.ti.com

.

Table 1. EVM-Compatible Device Data Sheets

Device

Literature Number

Device

Literature Number

ADS1120

SBAS535

MSP430F5528

SLAS590

ADS1220

SBAS501

TPS3838L30

SLVS292

SN74LVC2G157

SCES207

SN74LVC125A

SCAS290

TPS76333

SLVS181

MSP430, ADCPro are trademarks of Texas Instruments.
SPI is a trademark of Motorola.
I

2

C is a trademark of NXP Semiconductors.

Omega is a registered trademark of Omega Engineering Limited.
Samtec is a trademark of Samtec, Inc.
Vishay is a registered trademark of Vishay Intertechnology, Inc.
All other trademarks are the property of their respective owners.

1

SBAU203 – July 2013

ADS1x20EVM

Submit Documentation Feedback

Copyright © 2013, Texas Instruments Incorporated

Summary of Contents for ADS1 20EVM Series
























Reviews: