Texas Instruments ADC31JB68 User Manual Download Page 15 | Manualshive

Page: 15 / 20

Texas Instruments ADC31JB68 User Manual Download Page 15

LED Descriptions

15

SLAU630A – August 2015 – Revised August 2016

Submit Documentation Feedback

Copyright © 2015–2016, Texas Instruments Incorporated

Revision History

A.3

LED Descriptions

The EVM LEDs are described

Table 9. LED Descriptions

LED

Description

LED3.3

Indicates status of JESD204B link:
OFF: JESD204B link is not established
ON: JESD204B link is established

Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Original (August 2016) to A Revision

.....................................................................................................

Page

•

+5-V power supply removed and replaced with cable with flying leads in

Required Hardware

section.

......................

•

In the

Hardware Setup Procedure

section, updated the

Quick Start Test Setup

figure and the

TSW14J56EVM Setup

and

ADC31JB68EVM Setup

sections.

.......................................................................................................

«
...
13
14
15
16
17
...
»

Summary of Contents for ADC31JB68





















Reviews:

No comments