6
Instructions for use and maintenance
EN
•
Tighten the fixing screws A and B into the wall and
fix the appliance fully in points C and D.
•
Connect the flexible aluminium pipe to the outlet
of the range hood and to the chimney, taking into
account that the bends and curves reduce the
absorption power, so it is good to keep them at
minimum.
•
Ensure that the connection will not get loose when
the appliance operates at maximum power.
•
The joint bar (10) should be mounted on the wall by
means of screws (9).
•
Fix the internal chimney body (1) to the joint bar (11)
•
Place the external chimney body (2) and fix it at its
lower edge.
RISK OF ELECTRIC SHOCK!
Do not bend or crush the power cord during
installation! Otherwise the cord may get damaged.
RISK OF INJURY!
There is risk of injury during installation because
of the sharp edges. During installation always use
protective gloves.
All safety bolts and safety covers shall be installed in the
way specified in the instructions, otherwise the appliance
may fall.
OPERATION OF THE RANGE HOOD
The accessible parts may get hot while the
appliance is operating in combination with
operating hot plates under it.
CH 3420 1T 60 G range hood is operated by five round
buttons located on the front panel for comfortable and
easy access. The rightmost button is for switching on/off
the lightening, and the remaining four buttons are for
control of the ventilation speed.
Figure 5 – Control buttons of CH 3420 1T 60 G
Description of the control buttons shown in figure 5:
– Button for switching off the ventilation
I
– 1
st
ventilation speed
II
– 2
nd
ventilation speed
III
– 3
rd
ventilation speed
– Button for switching on/off the lightening
You can set the range hood to operate at a ventilation
speed which you wish, for example speed III, and you can
switch directly to speed I or go back to speed III or the other
way round.
OPERATING THE RANGE HOOD WITH AND
WITHOUT ACTIVE CARBON
Do not use the appliance without filters!
TESY range hoods are intended for use with standard
aluminium filters and also with filters with carbon which
may be purchased separately.
If there is not a chimney in the room the range hood shall
be used with a carbon filter to clean the air. This filter
is not included in the package, but you can purchase
it from Your supplier or service centre. In this manner
of operation the filter shall be replaced with a new one
every 3 to 5 months depending on the frequency of use.
Never wash the carbon filter. Keep it away from
children.
Before replacing the carbon filter You must switch
off the power supply of the range hood by
unplugging the power cord from the socket or by
switching off the circuit breaker.
The carbon filters come in a pair (left and right) and you
need to observe their direction during installation.
Figure 6 – Installation of the carbon filters.
Replacement of the carbon filters is done as follows:
1.
Place the filter in its correct place.
2.
Turn in a clockwise direction to fix it in its place.
Removal of the filters is done in the reverse order.
Lamp replacement
Before replacing the lamp You must disconnect
the appliance from the mains. Let the lamp cool
down, otherwise You may burn yourself.
•
Remove the aluminium filters.
•
Unscrew the faulty lamp in counter clockwise
direction.
•
Screw the new lamp in clockwise direction.
•
Reinstall the aluminium filters.
Summary of Contents for CH34201T60G
