Tesoro mMAX BANDIDO, Operator'S Instruction Manual

Page: 5 / 10

Product
Detectors
Coils
Accessories
Catalog
Dealers
Information
Frequently Asked
Questions
About Tesoro
Manuals
Field Tests
Articles
Testimonials
Customer Finds
Forums
Service
Warranty Repair
Contact Us
µMAX BANDIDO OPERATOR INSTRUCTION MANUAL
CONGRATULATIONS!
Your new Tesoro µMAX Bandido Metal Detector is part of a new series of detectors designed to provide you with many
happy hours of enjoyment in the most rewarding hobby I can think of – treasure hunting. Ahead of you lie fascinating and
exciting experiences as you step into the past – uncovering artifacts lost by past generations – or, as you take pleasure in
the great outdoors with family and friends searching for precious metals. I wish we could share these experiences with you,
and all of us at Tesoro wish you the best of success.
Your Tesoro µMAX detector is capable of meeting your needs in a wide range of treasure hunting situations. As with any
other metal detector, familiarity with this instrument is probably the limiting factor in determining how successful you can be. I
recommend that you read this manual and understand fully how to operate this detector before attempting to use it in the field.
As you become more familiar with your detector through practice, your rate of success will increase dramatically.
The µMAX Bandido is a precision electronic instrument that will last for years if properly cared for. Treat it right and it
won't let you down.
Good Hunting! Jack Gifford
INTRODUCTION
To be successful in treasure hunting with a detector you must:
l
Use a high­performance metal detector designed for the type of treasure hunting you will be doing.
l
Learn how to use your metal detector properly.
l
Search where there is buried treasure to be found.
l
Be persistent.
The µMAX Bandido is a true all ­purpose detector. It was designed for top performance in the widest range of detecting uses possible. It is
sensitive to small gold particles, it is powerful enough to relic and cache hunt with, it is plenty fast enough for competition hunting and it is great
for coin hunting. Yet, even with its amazing power, it is still easy to use.
This OPERATOR INSTRUCTION MANUAL is designed to help you learn to operate the detector properly for maximum performance in various
search conditions. Complete instructions on how to operate the µMAX Bandido are found in the two main sections: GETTING STARTED and
OPERATING TECHNIQUES.
If you are new to metal detecting, we highly recommend reading and following the entire GETTING STARTED section to develop the "feel"
of your detector. Then, study and practice the OPERATING TECHNIQUES section – especially Ground Balancing – to get the best performance
from your detector.
If you are new to treasure hunting with metal detectors, keep in mind that if there are no valuable metal objects buried where you are
searching, it won't matter how good your metal detector is or how skilled and persistent you are. To learn more about where to search for valuable
buried metals check with your metal detector dealer or book ­seller for magazines and books on treasure hunting.
GENERAL DESCRIPTION
The µMAX Bandido is one of the first of its kind: an ultra ­light weight, compact detector that packs the power and performance of the best full
size, heavier detectors. By utilizing state ­of­the ­art circuitry, Tesoro has created an amazingly versatile and powerful, easy to operate detector that's
perfect for all types of detecting, and for travel.
The µMAX Bandido is a Transmitter ­Receiver (TR) type of detector that operates in the Very Low Frequency (VLF) portion of the Radio
Frequency (RF) spectrum. The µMAX Bandido uses only three control knobs and two toggle switches to provide full VLF capabilities.
The performance of the µMAX Bandido will satisfy the requirements of the serious detectorists, whether experienced or novice. At the centre
of the µMAX Bandido is a special Hybrid circuit board developed from Surface Mount Technology that incorporates Tesoro's proven High Gain
Sensitivity Circuitry. This circuit board helps provide greater depths and more sensitivity to smaller, less conductive metal objects or "targets" such
as fine gold jewelry.
The µMAX Bandido has features that make its power easy to use. Through simple and fast operator adjusted "ground balancing," the ground
rejection circuitry will allow operation in even the most difficult ground mineralization conditions. Two operating modes and two tuning modes
add to the versatility of the detector's operation. The Discriminate Mode is Silent Search, meaning the searchcoil must be moving to detect a
target. The All Metal Mode is no ­motion, meaning the searchcoil will detect a target located directly under it, even when the searchcoil is not
moving. Auto Tune, the automatic tuning mode, is fast and retunes the detector in seconds after encountering a target. Normal Tune gives the
operator total control of retuning at the touch of a switch.
The electronic miniaturization of Surface Mount Technology permits the complex, powerful circuitry of the µMAX detectors to fit into a very
small space. The result is a detector that is so incredibly light there is no need to body mount the control housing. This exclusive design feature
adds to the µMAX Bandido's ease of use and makes those longer searches more enjoyable.
The µMAX Bandido comes with an 8" round concentric searchcoil for best all ­around performance with good depth. A variety of optional
Tesoro searchcoils are also available and will enhance the detector's performance under various conditions (see OPTIONAL ACCESSORIES).
GETTING STARTED ­ UNPACKING THE BOX
Your µMAX Bandido was shipped with these parts:
1 Upper Pole Assembly
Fully assembled, including upper pole stem with handle grip, padded arm bracket and control housing.
1 Lower Pole Assembly
Fully assembled, including middle pole stem with knurled nut, lower pole stem, and nylon pole tip complete with two thick friction
washers, mounting screw, lock washer and thumb nut.
1 8" round, concentric searchcoil with 3' cable
1 9 Volt Alkaline Battery
1 Extra set of two thin friction washers
1 Operator Instruction Manual
1 Tesoro Warranty Card
If any of these items are missing, contact the Tesoro Authorized Dealer where you purchased your detector immediately.
Assembly of the µMAX Bandido is simple and requires no special tools. Just Install the battery, mount the searchcoil on the lower pole
assembly, connect the two pole assemblies together, wrap the excess cable around the pole and plug the cable into the control housing. Finally,
adjust the pole length and searchcoil angle and you're ready!
INSTALL THE BATTERY
Your µMAX Bandido is equipped with an automatic battery test circuit so that you can always be sure you are getting top performance. The
battery should be checked after the detector has been on for about 10 minutes, and then periodically when used for long durations. For more
detailed information go to Performing the Audio Battery Test under TUNING YOUR DETECTOR.
To install or replace the battery, first make sure the SENSITIVITY control is set to POW OFF ­ turned completely counterclockwise past the
"click". Remove the battery door from the back of the control housing. Do this by pressing your thumb firmly on the louvered square ­ at the bottom
of the battery door ­ and sliding the battery door upward (in the direction of the arrow) while pushing.
Connect a fresh single 9 volt alkaline battery to the battery lead terminals. Make certain the polarity snaps to fit properly. A poor connection
may cause the detector to act erratically or fail to operate completely.
Place the battery into the battery compartment without pulling or stretching the battery lead wires. Replace the battery door by sliding it into
place making sure the upper mount slots are in line and the lock tongue is snapped into place.
ASSEMBLING YOUR DETECTOR
1. On the lower pole assembly, grasp the pole tip firmly in one hand. With the other hand, fully depress the two spring buttons on the
opposite end of the assembly.
2. Pull the middle stem out far enough for the spring buttons to click into the first set of the adjustment holes ­ locking the assembly into
place again.
3. Remove the mounting screw and thumb nut from the black nylon pole tip.
4. Insert the pole tip between the mounting ears and the searchcoil and align the holes of the pole tip and washers with those of the
mounting ears.
Note: the pole tip should fit very snugly into the mounting ears, however, it may be necessary to use the thin friction washers instead.
5. Insert the mounting screw through the holes in the mounting ears and pole tip ­ entering from the side opposite the cable connection.
6. Install the thumb nut on the mounting screw and tighten by hand.
Note: Do not over tighten the thumb nut. It should be snug, but not too difficult to loosen up.
7. On the upper pole assembly, depress the two spring buttons and slide the upper assembly into the lower pole assembly until the spring
buttons click into the holes ­ locking the two assemblies into place. Tighten the knurled nut to secure the two assemblies together.
Note: Do not allow the cable to flop loosely over the searchcoil. Since the detector is sensitive enough to “see ” the tiny wires in the
cable, a floppy cable can cause false signals as the searchcoil senses the moving wires.
8. Wrap the cable around the pole leaving enough slack near the searchcoil to permit searchcoil adjustment.
Note: Do not allow the cable to flop loosely over the search coil. Since the detector is sensitive enough to "see" the tiny wires in the
cable, a floppy cable can cause false signals as the searchcoil senses the moving wires.
9. Plug the male cable end into the female connector on the control housing and tighten the cable thumb nut. You are finished!
Note: You will want to adjust the pole length and searchcoil angle to your preference.
ADJUSTING THE POLE & SEARCHCOIL
The pole length should be adjusted so that the detector does not become uncomfortable or tiring after
long periods of use. The detector grip should rest in your hand with your arm relaxed, your elbow straight but
not locked, with the pole extending out in front of you at the approximate angle shown in the photo.
You should be able to swing the detector back and forth in front of you —using relaxed shoulder
movement —while keeping the searchcoil as close to the ground as possible. This swinging movement is often
called a “sweep.”
The searchcoil should not touch the ground during your sweep. The pole length should be adjusted to
allow this without having to lift the detector with your elbow or shoulder. The searchcoil should rest about one
inch above the ground while you are standing erect. The angle of the searchcoil should allow the bottom to
be parallel to the ground.
The pole length is adjusted by depressing the spring buttons and extending or shortening the pole until
the spring buttons click into the set of holes that give you the most comfortable pole length.
To adjust the searchcoil angle, simply loosen the searchcoil thumb nut slightly and move the searchcoil
into the desired position. Tighten the searchcoil thumb nut by hand so that the searchcoil will hold in place.
QUICKSTART ­ SELF GUIDED TUTORIAL
The QuickStart is designed to help you use your new µMAX Bandido metal detector right away, even if
you have never used a metal detector before. Just follow each easy step carefully and you'll quickly see how the basic detector functions work.
You'll also be introduced to some important concepts on the way.
Here's what you will need:
1. Your fully assembled µMAX Bandido metal detector
2. Three newer coins: a penny*, a nickel and a quarter
3. A nonmetal table or counter surface
4. Approximately 20 minutes to complete the QuickStart
*must be 1984 or newer ­ made of zinc
Here’s what you will do:
1. Perform an Audio Battery Test
2. Adjust the SENSITIVITY control
3. Perform an air test in All Metal Mode
4. Perform an air test in Discriminate Mode
Prepare for the Quickstart
Place your assembled µMAX Bandido on the nonmetal surface. Make sure there are no metal objects near the coil. Remove any jewelry from
your hands and wrists.
Start with these control settings:
l
DISC LEVEL control set to MIN
l
SENSITIVTY control set to POW OFF
l
TUNE switch set to NORM
l
MODE swith set to DISC
l
GROUND control set to the middle of its range:
turn it 5 complete turns counterclockwise then,
turn it 2 complete turns clockwise and stop.
The GROUND control should be left at this setting for the entire QuickStart.
Step 1 ­ Perform an Audio Battery Test
l
Turn the SENSIIVITY control from POW OFF to 1
You will hear the battery test tone for a few seconds as the battery is automatically tested. When the tone stops the detector is on the controls
are ready for adjusting.
Function Demonstrated: How the battery test tone will tell you the battery is working each time the detector is turned on.
NOTE: You should always perform the Audio Battery Test with Mode Switch set to DISC.
Step 2 ­ Adjust the SENSITIVITY control
n
Turn the SENSITIVITY control from 1 to 8
This is a good setting to begin with each time you use your detector. Leave the control at this setting for the rest of the QuickStart.
Function Demonstrated: Where to set the SENSITIVITY control for basic operation.
Step 3 ­ Perform an air test in All Metal Mode
Identify the Threshold Sound
Identify Target Response
Retune the Threshold
l
Flip the MODE switch to ALL METAL
Listen to the continuous, fairly even tone. This is called the "threshold sound". You will hear the threshold sound only when operating the
detector in All Metal Mode.
Hold the quarter in your fingertips and move the quarter from side to side about 12 inches from the front of the searchcoil.
Gradually move the quarter closer to the searchcoil ­ as you continue to move it from side to side ­ until you hear the threshold sound
increase. This increase in volume is called the "target response sound".
Continue to move the coin to test the target response sound. As you do this, try varying the distance or angle of the coin. Try varying the
speed you move the coin. Try holding the cold still and then moving it slightly. Try passing it in front of the edge of the searchcoil and then under
the center. Notice the differences in the target response sound with each change.
Repeat the test with each coin. Notice that the detector responds to each coin although the target response sound may vary, sometimes subtly.
Your detector will respond to objects made of any kind of metal when the object is in the searchcoil's sensitivity area or "range". Operating your
detector in this way is called a "no ­motion All Metal Mode with Normal Tune".
Retuning the threshold
Hold the quarter still about 2 to 4 inches from the searchcoil, in line with the searchcoil center. Listen to the target response sound for 1 or 2
seconds. Do not move the quarter!
l
Flip the MODE switch to RETUNE and release it
Notice that the target response sound will decrease to the regular level of the threshold sound. Now, slowly move the quarter from side to side,
going past the edge of the searchcoil. Notice the regular threshold sound is gone and the target response sound is now a "beep" that occurs when
the target passes in front of the searchcoil center . This technique is used to "pinpoint" the exact location of an object.
Take the quarter away from the searchcoil.
l
Flip the MODE switch toe RETUNE and release it
Notice the regular threshold returns. Move the quarter close to the searchcoil and notice the loud continuous target response sound has
returned. Take the quarter away again.
l
Flip the TUNE switch to AUTO
Hold the quarter still near the searchcoil for a few second and notice the detector automatically retunes itself. Then, try moving the coin from
side to side and notice the target response sound is a "beep". Take the quarter away from the searchcoil for a few seconds and try it again. Now, try
this test with the different coins using both tuning methods and list for the differences in the sounds.
Functions Demonstrated: 1) How the All Metal Mode target response sound will vary depending on the various factors such as what type of
metal targets are buried in the ground, how deep they are, how fast you move your searchcoil and so on. 2) How the detector's threshold can return
manually in Normal Tune or automatically in Auto Tune and how this effects the target response sound.
Step 4 ­ Perform an air test in Discriminate Mode
Identify the Target Response
Use Discrimination
l
Flip the MODE switch to DISC
l
Leave the DISC LEVEL control set to MIN
NOTE: In Discriminate Mode, you will not hear the continuous threshold sound of the All Metal Mode, so returning is not needed.
Hold the quarter in your hand and move the quarter back and forth about 12 inches in front of the searchcoil bottom.
Gradually move the quarter closer to the searchcoil ­ as you continue to move it back and forth ­ until you hear a "beep". This beep the target
response sound.
Continue to move the coin to test the target response sound. As you do this, try varying the distance or angle of the coin. Try varying the
speed you move the coin. Try holding the coin still then moving it slightly. Notice the difference in the target response sound with each change.
Repeat the test with each coin. Notice that the detector responds to each coin although the target response sound may vary. Your detector can
respond to objects made of any kind of metal if there is movement between the object and the detector. Operating your detector in this way is
called a "Silent Search".
l
Turn the DISC LEVEL control from MIN to MAX
Pass the quarter back and forth in front of and close to the searchcoil bottom. Notice the sound as the coin nears the center of the searchcoil.
Now, try this with the nickel and then the zinc penny. Notice there is no sound with these two coins. The ability of a metal detector to ignore
certain types of metal that it encounters is called "discrimination". Using your detector in this way is called a "Silent Search Discriminate Mode".
Control settings to ignore most zinc and nickel objects can be:
l
MODE switch ­ DISC
l
DISC LEVEL ­ MAX
l
Move the DISC LEVEL control from MAX to 7
Pass each of the three coins in front of the coil. Notice the quarter and the zinc penny now cause a target response sound.
Control settings to ignore most nickel can be:
l
MODE switch ­ DISC
l
DISC LEVEL ­ 7
l
Now move the DISC LEVEL control from 7 to 4
Pass each of the three coins in front of the searchcoil. Notice all three coins now cause a target response sound.
Control settings to include newer US coins while excluding most iron objects can be:
l
MODE switch ­ DISC
l
DISC LEVEL ­ 4
Functions Demonstrated: 1 ) T h e m o t i o n ­based operation and target response sound of Silent Search Discriminate Mode. 2) How the
Discriminate Mode can be used to help determine the types of metal a target may be. By adjusting the DISC LEVEL control you can select what
metals your detector will ignore.
Conclusion
Well done! You have finished the QuickStart Guide and have operated many of the basic detecting features of the µMAX Bandido. You have
also been introduced to the ideas of: 1) "target response sound", 2) "threshold sound", 3) "returning the threshold", 4) "target discrimination" and 5)
"target pinpointing".
Now you are almost ready to begin the journey into the art of metal detecting by actually using your detector to find buried metal. But first a
word about air tests.
The air tests in the QuickStart are of limited value. Metal detectors perform differently in air tests than when in actual use "in the field". Tesoro
detectors are specifically designed to deliver the best performance in the field.
The OPERATING TECHNIQUES and TUNING YOUR DETECTOR sections will give you more detailed information on how to set your
detector's controls, especially selecting a tuning mode and using discrimination, for the best results.
Before you use your µMAX Bandido in the field you need to learn how to operate one more features: the GROUND control. Using the
GROUND control to properly "Ground Balance" your µMAX Bandido will allow you to tap into its full power and performance capabilities and is
perhaps the most important feature to master. The Ground Balance section will explain step ­by­step how to use this feature.
Finally, the only way you can become truly proficient at using your detector to find buried treasure is to use it in the field and learn from
experience! However, we strongly suggest that you read this entire manual to become proficient with all of the features as you continue to use your
detector.
You have the finest tool available, now all you need is the skill that comes from experience.
TO TURN YOUR DETECTOR OFF:
l
TURN THE SENSITIVITY CONTROL TO POW OFF
Counterclockwise past the "click".
TO TURN YOUR DETECTOR ON:
l
MAKE SURE THE MODE SWITCH IS SET TO DISC
l
TURN THE SENSITIVITY CONTROL TO 1
Clockwise past the "click".
OPERATING TECHNIQUES ­ CONTROLS
The µMAX Bandido has only five controls, all mounted on the front panel of the housing for fingertip adjustment. How these controls should
be set for peak performance will depend on the type of metal you are searching for, search site conditions, mineral content of the soil and so forth.
Use the information in this section and the TUNING YOUR DETECTOR section as a basis for setting the controls on your detector. Using your
detector in the field will allow you to learn the detector's responses to various conditions and will guide you in fine tuning the detector's operating
controls.
SENSITIVITY ­ ON/OFF Sensitivity Control
This rotary switch control has three functions:
l
Turns the detector ON and OFF
l
Activates the automatic Audio Battery Test
l
Adjusts the Sensitivity Level
NOTE: The detector should always be turned off when not in use.
Turning the SENSITIVITY knob clockwise past the initial "click" turns the detector on and actives the automatic Audio Battery Test circuit. This
test will give you a sound, usually lasting several seconds, that indicates the battery's condition. When the Audio Battery Test is over, the detector ’s
Sensitivity Level can be adjusted.
Turning the SENSITIVITY knob clockwise increases the detector's Sensitivity Level. The level from 1 up to 10 is the normal range. This range
corresponds with the normal Sensitivity on standard detector's. Turning the SENSITIVITY knob past 10 into the orange area puts the Sensitivity
into the MAXBoost range found only the µMAX detectors.
NOTE: It is best to turn the detector on in Discriminate Mode. Since the Discriminate Mode is a silent mode with no continuous threshold
sound, it will be obvious when the Audio Battery Test is complete.
If you turn the detector on in All Metal Mode the Audio Battery Test sound will be immediately followed by the threshold sound. This may
make it difficult to hear the battery test end and discern the battery condition.
Also, the Sensitivity Level is best set while in the Discriminate Mode. After the Audio Batter Test is over and the Sensitivity Level is properly
set, you may change the operating mode to All Metal without difficulty.
DIST LEVEL ­ Discrimination Level Control
This rotary switch control has one function:
l
Adjusts the Discrimination Level.
Once the detector is in the Discriminate Mode, the DISC LEVEL control is used to adjust the detector's Discrimination Level. Turning the DISC
LEVEL knob clockwise increases the detector ’s Discrimination Level and vice versa.
NOTE: When the detector is operating in the All Metal Mode the DISC LEVEL control is not used.
TUNE ­ Tuning Mode Selection Switch
This toggle switch has one function:
l
Sets the Tuning Mode: Normal or Auto
This toggle has to positions: To the right ­ labeled AUTO ­ it locks in place and sets the threshold tune method to Automatic. To the left ­
labeled NORM ­ the locks the place and sets the threshold tune method to Normal. NOTE: The tuning Mode is used only when operating in the All
Metal Mode.
MODE ­ Mode Selection / Retune Switch
The combination toggle switch has two functions.
l
Sets the operating mode: All Metal or Discriminate
l
Retunes the threshold in All Metal Mode.
This toggle has three positions: To the right ­ labeled DISC ­ it locks in place and sets the operating mode to Discriminate. To the center ­
labeled ALL MET ­ it locks in place and sets the operating mode to All Metal. To the left ­ labeled RETUNE ­ it spring returns to the center
position and retunes the detector ’s threshold while remaining in All Metal Mode. So, this combo switch functions as a Retune Switch by pressing
the switch completely to the left and releasing it so it springs back to the center position.
NOTE: Manual retuning (MODE/RETUNE) is used only when operating in the All Metal Mode with Tuning set to Normal (TUNE/NORM).
GROUND ­ Ground Balance Control
This rotary switch control has one function:
l
Adjusts the Ground Balance
This control adjusts the All Metal Mode sampling so that the µMAX Bandido ignores the normal ground mineralization. Making this
adjustment is often called "Ground Balancing". The knob will turn continually in either direction, although its effect use range is only 3 ¾ turns.
Once you have turned the knob to the end of its use range in either direction, you should notice a slight increase in "drag" as the knob is turned.
When you feel the "drag" you may immediately reverse direction to enter the effective use range of the next 3 ¾ turns.
NOTE: The GROUND control does affect both operating modes by should be adjusted in All Metal Mode.
TUNING YOUR DETECTOR
Every detector must be properly tuned in order to perform at its peak and provide maximum depth. In fact, the more powerful a detector is, the
more critical the tuning becomes. Less powerful detectors are more tolerant of improper tuning, but are also not capable of the depth of a properly
tuned high power detector such as the µMAX Bandido. To achieve peak performance from your µMAX Bandido, be sure to properly adjust the
GROUND control in the All Metal Mode. The settings of this control will also affect the detector ’s performance in Discriminate Mode, so make sure
to adjust it properly first, even if you will not be hunting in All Metal Mode. Remember: improper tuning will reduce performance and can also
cause "false" and erroneous "ghosting signals".
Tuning your µMAX Bandido can be done in 5 simple steps:
1. Ground Balancing the detector using the GROUND control.
2. Setting the operating mode using the MODE switch.
3. Setting the tuning mode using the TUNE switch.
4. Setting the Sensitivity level using the SENSITIVITY control.
5. Setting the Discrimination level using the DISC LEVEL control.
NOTE: Ground Balancing should be done while in All Metal Mode and Auto Tune Mode. Setting the Discrimination Level and the Sensitivity
Level should be done while operating in Discriminate Mode.
Ground Balancing
Ground Balancing is not a difficult procedure, but it is critical if you desire maximum depth and stability. It is especially important if you plan
to gold nugget hunt for match ­head sized or smaller nuggets in a highly mineralized ground.
NOTE: No matter where you will be searching, or whether you will be operating in the All Metal Mode or Discriminate Mode, make sure the
detector is properly Ground Balanced in the All Metal Mode with Auto Tune Mode first.
Start with these control settings:
l
DISC LEVEL control set to MIN
l
SENSITIVITY control set to POW OFF
l
TUNE switch set to AUTO
l
MODE switch set to ALL METAL
l
GROUND control set to the middle of its range
turn it 5 complete turns counterclockwise then,
turn it 2 complete turns clockwise and stop
Next:
l
Turn the SENSITIVITY control set to 10
Wait 3 to 4 seconds until the Audio Battery test is complete.
Raise the searchcoil to 6 to 8 inches above the ground, level and parallel to the ground. While listening to the threshold sound, lower the
searchcoil quickly to the ground level and listen to what the threshold sound does.
One of three things will happen to the sound: 1) the sound will increase, 2) the sound will go silent, or 3) the sound will remain the same.
Which one of these happens will determine what you need to do to properly Ground Balance your detector for the area you are at.
1) If the threshold sound gets louder when you lower the searchcoil, it means the GROUND knob needs to go the left.
2) If the detector goes silent and you lose the threshold sound momentarily, then you will need to turn the GROUND knob to the right.
3) If there is no change in the threshold sound as you lower the searchcoil to the ground, then you just happen to already have the proper
ground balance and can proceed to hunt.
Start out using slight turns of the GROUND knob, the distance of the movement being equivalent to about one hour on a clock face. The
entire effective area of this control is 3 ¾ turns from minimum to maximum, so if you start Ground Balancing in the middle of the effective range it
will only take about two complete turns in either direction to be at one end of the effective range.
NOTE: There are three important things to remember when Ground Balancing with this method.
First, you are in the Auto Tune mode and once you hesitate at ground level for a second or two, the detector will retune the threshold
automatically. Therefore, when you lower the searchcoil toward the ground, you are only listening for the initial change in volume.
Second, make you are Ground Balancing in a clean area and not lowering the searchcoil down over a piece of metal.
Third, when you raise the searchcoil be sure that you DO NOT tilt the searchcoil at an angle.
By continually "pumping" the searchcoil from 6 to 8 inches above the ground to ground level and back up in the air again while turning the
GROUND knob in the appropriate direction, you will very quickly reach the point where there is the absolute minimal change in threshold sound
during the pumping. When you have reached that point you are "Ground Balanced" and can begin searching the area.
NOTE: Changing ground mineralization may make occasional small adjustments to the GROUND knob necessary to maintain peak
performance.
Selecting the proper operating mode
The µMAX Bandido offers two operating modes, All Metal Mode and Discriminate Mode.
The Discriminate Mode is "Silent Search" operating mode. This means that the detector will make no sound until it encounters a metal target.
This mode requires that the searchcoil be moving slightly for target detection.
The All Metal Mode, however, is a "no ­motion" operation mode. This means that the detector will emit a continuous "threshold sound" until it
encounters a metal target at which time the sound will noticeably increase. This mode does not require motion so the searchcoil can be held still
for target detection if needed.
The All Metal Mode, as the name implies, will detect all types of metal targets. When operating in this mode you will find unwanted "trash"
metal objects such as nails, foil, pull tabs, etc., just as you would with any high ­performance detector. The All Metal Mode is preferred for hunting
relics, artifacts and other objects that are made of non ­precious metals ­ especially iron. This mode is also good for beach hunting where the sand
allows easy digging and time wasted on digging up trash metal objects is not a major concern.
The All Metal Mode must be used for gold nugget hunting, since the response to small gold items is so close to iron. For most nugget hunting,
the All Metal Mode & Auto Tune Mode combination will provide the best performance although some special attention for hot rocks may be
necessary (see Selecting he proper tuning mode ).
The Discriminate Mode will allow you to control the detector's response to most of the common trash metal objects found in school yards,
parks, and beaches. Discriminate mode is generally used for "coin shooting" such areas where you prefer to avoid wasting time digging up
common trash metal. The Discrimination Level you select will determine what types of metal your detector will ignore.
In many other metal detectors, the All Metal Mode offers greater depth ­ up to 30% over the Discrimination Mode. Not so with the µMAX
detectors. The new µMAX circuitry with MAXBoost overcomes this common problem and delivers superior sensitivity and better depth in both
operating modes.
Selecting the proper tuning mode
The Auto Tune Mode (TUNE ­AUTO) on the µMAX Bandido is a fast automatic tuning that takes just 2 to 3 seconds to automatically adjust
itself. The Auto Tune quickly retunes the detector to its established threshold following a target response.
Auto Tune Mode also keeps the detector's signal from drifting. This tuning mode offers maximum stability while searching in All Metal Mode
and is recommend for gold nugget hunting.
The Normal Tuning Mode (TUNE ­NORM) will hold a target's signal without retuning for as long as the searchcoil is held stationary directly
over the target. Some drift may occur in this mode, but is quickly remedied by manually retuning using the MODE switch (MODE ­RETUNE). For
precise pinpointing, identifying target size, line tracing and ore sampling in All Metal Mode, use the Normal Tune Mode.
Fast automatic tuning can cause an "overshoot signal" on "hot rocks" ­ that is, a momentary silence as the searchcoil sweeps over an extremely
mineralized rock, followed by a loud "boing" sound when the searchcoil passes clear of it. This sound is so different from a good target response
sound, that it is easily recognized. (The only problem with just ignoring these sounds overshoot signals is that a small gold nugget may be hiding
beneath the hot rock). Also, the Auto Tuning Mode will cause a “nulling ” of the threshold sound when the searchcoil sweeps over a very strong
metal target.
Setting the Sensitivity Level
In lightly to moderately mineralized ground, you can usually set the SENSITIVITY control as high as 8 to 10 (normal maximum setting). In the
right conditions you can move the SENSITIVITY into the MAXBoost area for increased depth.
To adjust the Sensitivity Level to your search conditions, first set the operating mode to DISC and turn the SENSITIVITY control clockwise as
far as possible until the detector just begins to "chirp" intermittently. If the chirping is too frequent, simply turn the control counterclockwise just
enough to cause the chirping to subside. Once set, this control should not require readjusting unless site conditions change.
Occasionally you may need to reduce the setting to eliminate "false signals" caused by difficult conditions. Some of the many things that can
cause the response of the detector to become erratic during regular use are very large targets, highly mineralized ground on trashy sites, intense
ground mineralization changes, CB radios, radio and TV broadcasting antennas, and nearby sources of electrical interference.
These false signals are generally short, choppy sounds that are not repeatable and therefore, can easily be distinguished from a good target
response sound. They can be distracting, though, and reducing the Sensitivity level will help reduce these signals with an accompanying loss of
target sensitivity.
Extreme conditions such as salt ­wet sand may require you to lower your Sensitivity setting into the 2 to 5 range. Overall, you should always set
the Sensitivity control as high as possible, while still getting smooth operation.
NOTE: The no ­motion All Metal Mode of the µMAX Bandido is not affected by the SENSITIVITY control.
Setting the Sensitivity Level in MAXBoost
The MAXBoost feature is a high gain boost over and above the normal maximum of 10 and indicated by the orange area on the
SENSITIVITY control. Using MAXBoost will cause no harm to your detector but, in certain conditions it can result in the annoying chirping sounds
that may make it difficult to hear a good target response sound.
In ideal conditions MAXBoost can add inches of depth to your search with no chirping. In difficult conditions the extra depth will still be there
but heavy chirping may make the feature to difficult to use. You must determine when and how much of the MAXboost feature to use for your
search site conditions.
Setting the Discrimination Level
The DISC LEVEL control is used to adjust the detector's response to unwanted trash metal when operating in the Discriminate Mode. At the
lowest setting (MIN), the detector will ignore most iron objects, but will still respond to light foil, bottle caps, pull ­tabs and most other metal objects.
As the Discrimination Level is increased, more of these trash metal objects are ignored and give no target response sound when inside the
searchcoil ’s range.
The DISC LEVEL should be set to your desired "rejection level" for the particular area you are searching. We recommend starting at a low
setting if you are unsure of how much trash is in the area. Adjust the level higher if you find yourself digging more trash then you like. Remember
that with any metal detector, you will lose target response to small gold rings and nickels when discrimination is set at the pull ­tab rejection level.
So, digging some trash will increase your number of good finds.
The below diagram "DISC LEVEL ­ Discrimination Level Settings" shows the settings where many of the common metal objects are ignored
by a typical detector. Each detector can vary a little ­ due to manufacturing tolerance ­ so you should experiment with your detector and become
familiar with its rejection levels for these trash metal objects.
Earlier motion detectors that operated with a continuous "threshold" sound would give the user a definite indication of trash metal by either
"nulling" completely (no sound made temporarily) or by generating short, choppy sounds. Since the µMAX Bandido's Discriminate Mode is Silent
Search and operates without threshold sound, there is no nulling to indicate that the area is extremely trashy.
When searching in the Discriminate Mode we recommend that you periodically switch to All Metal Mode and check the area you are
searching to get an idea of how much trash is really there. In extremely trashy areas it may be desirable to switch to a smaller searchcoil, even
though doing so may cause a loss of depth. The smaller coil will allow you a better chance of finding coins between the close pieces of trash.
Performing the Audio Battery Test
Your µMAX Bandido is equipped with an automatic battery test circuit so that you can always be sure you are getting top performance from it.
The battery should be checked after the detector has been on for about 10 minutes and then periodically if you are using it for long periods.
To activate the Audio Battery Test, simply turn the detector off momentarily and then back on again. If the battery is fresh, the detector should
emit a continuous and loud "Beep" sound that lasts for about 4 or 5 seconds, and then slowly fades into silence. As the battery ages, this sound is
less intense and fades out more quickly. When you hear only a brief "buzz" or no sound at all, replace the battery with a fresh one.
If you prefer, a rechargeable Nickel ­Cadmium (Ni ­Cad) battery can be substitute for the standard 9 volt alkaline battery. Individual 9 volt size
Ni­Cad cells, as well as the chargers for them, are readily available at most electronic supply stores. They are installed into your detector in the
same manner as non ­rechargeable batteries. The Battery Test sound on a Ni ­Cad will be weaker than an alkaline in the beginning, but will not
weaken as much with use.
Controlling Audio Volume
The speaker in the µMAX does not have a volume control. The volume should be sufficient to accurately hear the target response sound in
most environments. If more or less volume is required in your particular situation we recommend using a set of good quality headphones with a
built ­in volume control.
FIELD USE
Handling Your Detector
The detector should be held in a position that is comfortable for you as shown in the "Adjusting the Pole & Searchcoil" section in "Getting
Started." Swing the detector from side to side in about a three foot arc, overlapping succeeding strokes well. This motion is called a “sweep.” The
µMAX Bandido was designed to get maximum depth without the frantic pace required of earlier motion detectors, so go at a pace that is
comfortable for you. In fact, trying to hunt too fast may even cause a loss of depth in heavily mineralized locations.
Regardless of which mode you are using, try to keep your searchcoil height constant and close to the ground. Most people tend to raise the
coil at the end of a sweep —much like a pendulum —especially if in a hurry. Try to avoid this, as any increase in height from the ground will cause
a corresponding loss of depth.
In areas with well ­kept lawns, the easiest way to maintain a constant searchcoil height is to allow the coil to rest on the grass as you sweep
from side to side. In rough and rocky areas, it is best not to “scrub” the coil on the ground, as the rocks will act like abrasives and wear away the coil
bottom (an optional coil scuff cover will protect against this). Sweep the coil as close to the ground as possible without touching. Hitting the ground
or rocks may cause a false signal much like a desired target would. Sweeping the coil too high above the ground results in a loss of depth.
Planting a Test Garden
To better learn how your detector will perform in the field, it would be helpful to bury some coins and trash metal junk items in an area that
you know is clear of other metal objects, and then try the µMAX Bandido in its two different operating modes. Check the area in All Metal Mode
first to be sure its clear of trash then bury the targets at least 1 foot apart, and from 2 to 4 inches deep to start. Make a map of the area to be sure
you know what each target is and how deep it is. Practice on these targets to familiarize yourself with your detector ’s target response. This will also
help you learn the proper sweep speed for best operation. This type of practice area is often called a “test garden ” or “test bed ” and is one of best
tools to help you develop your metal detecting skills.
Recognizing False Signals in Discriminate Mode
When operating in the Discriminate Mode, some “false signals ” may be caused by 1) heavy concentrations of trash metal objects, 2) very large
trash metal objects, or 3) electrical interference. These signals are generally short, choppy sounds and sound different than “good signals ” (good
target response sounds).
At the end of your sweep, as you the reverse the coil direction, the detector is most susceptible to trash induced noise. There are two ways to
tell whether these sounds are good deep signals or trash “noise. ” The first is by repeatability. Trash induced noises will not be regular as you sweep
the coil over the suspected target several times, whereas a good target response will be repeatable. The second method is to switch to All Metal
Mode and check the target response sound. If the response is weak, it may well be a deep, good target; but if the response is very strong, it is
probably trash. Note that a coin close to the surface can give a double beep sound, but it is regular and repeatable. Raising the coil an inch or two
will restore the single beep on surface targets.
When searching in the Discriminate Mode, it is best not to use a higher DISC LEVEL setting than necessary. Nickels and most smaller rings are
rejected when the DISC LEVEL is set to reject pull tabs on any metal detector that is a TR Discriminator like the µMAX Bandido. If you don ’t dig
any junk at all, you are surely passing up a lot of good finds as well. Set the DISC LEVEL only high enough to suit the conditions where you are
searching. If there is any doubt whether a target is good or not, dig it.
Pinpointing a Target
When pinpointing a target, the All Metal Mode/Normal Tuning Mode can offer advantages over Discriminate Mode, such as no false signals
and no need to move the searchcoil to get a target response.
A good method for pinpointing in All Metal mode is “X­ing ” the target with the searchcoil. Remember that the targets response sound is always
greatest when the target is directly under the center of the searchcoil. To “X” a target, sweep the searchcoil over the target from side to side and
them from front to back until you can identify the center of the X: the spot on the ground where the target response sound is the greatest. Hold your
searchcoil stationary over the center of the X and hit the RETUNE switch. Now repeat the X ­ing; this time watching for the exact spot —under the
coil center —where the detector beeps. That spot is where the target is located.
Pinpointing a target in Discriminate Mode is probably best done by “X­ing ” as well. Remember that the detector will beep just as the target
passes under the center of the searchcoil. Slowing the sweep speed down will help you pick out the center of the X because the target response is
reduced at very slow speeds making it easier to correlate the sound with the coil center.
Another easy method is to sweep the coil from side to side across the target in very short sweeps, as you slowly move forward and backward
across the target. Slow down the sweep rate and shorten the sweeps until you just barely get a response at one spot. The target will be directly
below the coil center at this response time.
Another method of pinpointing in Discriminate Mode is to quickly change to All Metal Mode to check the target response. Remember that All
Metal Mode is not susceptible to the false signals of Discriminate Mode and can sometimes give a clearer and more consistent response to difficult
targets such as a dime buried next to a pull ­tab. By switching back and forth between modes and comparing the target response sound in All Metal
to the target response sound in Discriminate you can often better identify the likely location of the target.
Finally, raising the searchcoil during pinpointing can also help by narrowing the response to the target. Practice pinpointing often, and you
will soon become more accurate and faster.
Recovering a Target
If the target is shallow and the soil is soft, you may be able to “probe ” and find the exact location of the target before you dig it. Since filling
all holes after you recover the target is so important, digging a small precise hole is best. If the target is deep, you may need to dig a larger hole.
As you dig, occasionally check the hole with your detector to see if you have moved the object, can probe it, or have already dug it. Be sure to fill
all holes after you recover the target. Two methods are shown on the next two pages that work most everywhere.
Be sure to protect your hobby by leaving the site cleaner than you found it and with all holes filled!
RECOMMENDED RECOVERY METHODS
GENERAL INFORMATION ­ CARE AND USE
Basic Care
The µMAX Bandido is a sturdy instrument but it is not designed to withstand abuse. In caring for your µMAX Bandido there are several
important “DO NOTs ” to remember. DO NOT use it to pry rocks loose or to beat bushes out of the way. DO NOT drop the machine into water. DO
NOT use it unprotected in the rain. DO NOT leave it exposed at night where dew could form on it. DO NOT store it in places that could get
extremely hot (next to a woodstove, in an attic). DO NOT leave it in the trunk of a car or in the back of a hatchback style car where high
temperatures could build up. DO NOT store it with the battery installed as batteries may leak. DO NOT spray lubricants such as WD­40, or any type
of cleaners, solvents, sealants or other chemicals into or onto the electronic parts, switches or controls. And finally: DO NOT attempt to modify or
repair the detector ’s electronics as this will void your detector's warranty.
THE WARRANTY DOES NOT COVER DAMAGE RESULTING FROM AN ACCIDENT, NEGLECT OR ABUSE.
Protecting Your Investment
So many detectorists are disappointed when their new detector slowly becomes less and less responsive and seems to have lost some of its
original performance. You can help avoid this from happening to your detector by following these basic care and protection guidelines.
l
Operate your detector exactly as recommended in this Operator Instruction Manual.
l
Use only high ­quality alkaline batteries of the correct voltage. Never substitute a different voltage. When using a Ni ­Cad battery, always
use a separate convertible pack with the proper voltage output for the detector ’s design.
l
Remove the battery from the detector after each use. This will prevent damage to the detector if the battery leaks.
l
The searchcoil cable is hard ­wired to the searchcoil and protected by a strain relief. Inspect the strain relief frequently to make sure it is
firmly attached and intact.
l
Keep cables properly wound around the pole stems and protect them during use. Floppy, pinched, or cables that become snagged
during use may short, causing erratic noises or unnecessary replacement of the searchcoil.
l
Sweep the searchcoil carefully, especially when using around rocks and building foundations. Avoid hitting the searchcoil against hard,
solid objects and surfaces.
l
Keep your searchcoil slightly off of the ground during the sweep, especially when using in gravel or hard, rocky dirt.
l
Always use a properly designed protective scuff cover on the searchcoil. (See "Optional Accessories" in the next section.)
l
Remove and clean out scuff covers periodically to avoid buildup of mineralized dirt particles which will affect performance.
l
The searchcoil is waterproof and can be submerged in either fresh or salt water. After the searchcoil is used in salt water, rinse it and the
lower stem assembly well with fresh water to prevent corrosion of the metal parts.
l
The searchcoil is waterproof but the electronics are not, so always prevent any moisture or water from entering the control housing and
never allow the cable connectors to become submerged in water.
l
If working in or near water, or if there is a possibility of rain, use a protective weather resistant pouch or plastic bag to cover the control
housing. Make sure it can "breathe" in order to ensure against condensation buildup inside.
l
After each use, clean the detector with a soft cloth to remove dust, moisture, or other contaminants.
l
When transporting the detector in a car during hot weather, store it on the floor of the passenger compartment if possible. Using a carry
bag gives additional protection. In any case, never allow the detector to roll around unprotected in the trunk or back of a pickup truck.
l
Protect your detector from dust, moisture, and extreme temperatures during storage.
l
When shipping, use the original factory carton or similar heavy ­duty container and provide a minimum one inch of padding around all
parts.
l
Treat your detector as you would any sensitive electronic instrument. Though ruggedly constructed and designed to withstand the
demands of normal treasure hunting, proper care is essential.
OPTIONAL ACCESSORIES
Tesoro Metal Detectors and genuine Tesoro Accessories are sold only through independent Tesoro Authorized Dealers, who are almost always
metal detectorists themselves. They can answer your questions about your Tesoro detector, what accessories may be helpful and about metal
detecting in general.
See your Tesoro Authorized Dealer for more information and prices on optional accessories.
Scuff Covers
We highly recommend using a scuff cover to protect your searchcoil at all times. The scuff cover for the µMAX Bandido fitted with the 8"
searchcoil is Tesoro Part # SCUFF ­8R­B.
Searchcoils
The 8" concentric searchcoil provided with the µMAX Bandido is designed for best all ­around performance. Optional searchcoils may add to
your detector's performance.
Smaller searchcoils give better “target separation ” ­ that is, more distinct target response for metal objects buried closely together ­ which is
very useful when hunting trashy sites. Very small searchcoils can deliver the best response and depth to small targets such as fine gold chains with
some sacrifice in depth on larger objects. Larger searchcoils give a wider sweep, covering more ground, greater depth especially on larger objects;
however, they may not detect some very small object such as half dimes and will have difficulty in very trashy areas.
Wide scan searchcoils ignore ground mineralization better than concentric searchcoils and may offer improved performance in extreme
ground conditions.
Selecting the right optional searchcoil depends on factors such as what you are searching for and search site conditions. No one searchcoil is
better than all the rest. Several optional interchangeable searchcoils are available for the µMAX. They are all easy to mount and require no
special tools. See the next page for a list of these searchcoils with the Tesoro part # and description.
Tesoro Searchcoils
Optional scuff covers are also available for any Tesoro searchcoil.
Headphones
Most metal detectorists prefer to use headphones instead of the detector's built ­in speaker. Headphones help block out background noise (such
as wind) and make it easier to hear faint signals. Headphones with a built ­in volume control will allow you to adjust the sound volume to your
preference.
SPECIFICATIONS
µMAX BANDIDO FEATURES
l
High Gain Sensitivity Circuitry — designed specifically to deliver greater depth, sensitivity and stability.
l
MAXBoost Feature — extra power of super high gain can add inches to discrimination search depth in ideal conditions.
l
High­sensitivity Searchcoil — a 8 inch open center concentric for broad sweep, good pinpointing and deep ground penetration.
l
Ultra­light Weight— search longer without fatigue.
l
3 piece Knockdown Pole — compact for storage and travel.
l
Turn­on­and­go­ makes storing and traveling convenient.
l
Two Operating Modes — motion ­based All Metal and Discriminate.
l
Easy to Operate ­ just two simple controls at your fingertips.
l
Economical Use — up to 20 hours plus on a single battery.
l
Tesoro Lifetime Warranty — our pledge of quality to you.
What it doesn't have.
A big, heavy, high ­powered speaker. Loud, heavy speakers are popular with many manufacturers. The "fuller" sound they produce gives the
illusion of greater sensitivity to small and deep targets —a great showroom sales tool! Most serious detectorists, however, hunt with headphones and
a µMAX will drive standard headphones well. If you choose not to use headphones, the µMAX speaker will be loud enough for most environments.
It will allow you to hear the small and deep targets found by the µMAX's high power circuitry —without excessive battery drain.
A hip mount, arm strap or battery recharging system. These kinds of "built ­in accessories” are simply unnecessary in a µMAX detector.
Under the copyright laws this documentation may not be copied, photocopied, reproduced, translated or reduced to any electronic or machine ­
readable form, in whole or in part, without the prior written consent of Tesoro Electronics Incorporated, except for the private use of a µMAX Bandido
owner or operator, or in a manner otherwise described in this documentation.
© 1995­1996 Tesoro Electronics Incorporated. All rights reserved. Printed in the United States.
The power and features of the Tesoro µMAX Bandido make it ideal for the serious
detectorist who wants top ­of­the­line performance and versatility in a lightweight, low ­cost
detector. It is also an ideal detector for a beginner who wants a machine they will never
outgrow.
WARRANTY SERVICE
Your Tesoro metal detector is covered by a Limited Lifetime Warranty , the terms of which
are listed below. If your metal detector should require service, you may return it to the Tesoro
factory at the address below.
LIMITED LIFETIME WARRANTY
This warranty gives you specific legal rights, and you may have other rights which vary from
state to state.
This instrument is warranted to be free of defects in material and workmanship as long as it
is owned by the original consumer purchaser. This warranty is not transferable and is valid only
if the warranty registration card has been completed and mailed within 10 days of purchase.
TESORO will, at its option, repair or replace any instrument covered by this warranty,
without charge, except for transportation charges, at its factory in Prescott, Arizona.
This warranty excludes batteries, damage caused by leaky batteries, cable breakage due to
flexing on body mount units, and wear of the searchcoil housing. Also excluded are instruments
which have been abused, altered, or repaired by an unauthorized party.
Tesoro Electronics, Inc. 715 White Spar Road Prescott, AZ, USA 86303 1­928 ­771 ­2646
Tesoro Part # Description
COIL­4RC 4" round concentric (closed center, white)
COIL­7RC 7" round concentric (closed center, white)
COIL­8RCW­B 8" round concentric weighted (open center, brown)
COIL­10.5RC 10 ½" round concentric (closed center, white)
COIL­7RW 7" round wide scan (closed center, white)
COIL­11RW 11" round wide scan (closed center, white)
Operating Frequency 12 kHz
Searchcoil Type Round, open center concentric
Searchcoil Size 8" diameter
Cable Length Approx. 3 ’
Audio Frequency Approx. 300 Hz
Audio Output 1½” speaker and headphone jack
Headphone Compatibility ¼” stereo plug
Weight (may vary slightly) 2.2 lbs.
Battery Requirement One 9 volt DC (alkaline)
Battery Life (typical) 10 to 20 hours
Optimum Temperature Range 30 ° to 100 ° F
Optimum Humidity 0 to 75% R.H.
Operating Modes
Silent Search All Metal
Silent Search Discriminate
Home