15
ENG
Full-integrated model
Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of dishwasher (see
figure A). After positioning of the panel, fix the panel onto the outer door by screws and bolts (See figure B).
Step 3. Tension adjustment of the door
1. The door springs are set at the factory to
2. the proper tension for the outer door. If an aesthetic
wooden panel is installed, you will have to adjust the
door spring tension. Rotate the adjusting screw to
drive the adjuster to strain or relax the steel cable.
Door spring tension is correct when the door remains
horizontal in the fully opened position, yet rises to a
close with the slight lift of a finger.
Step 4. Dishwasher installation steps
NOTE
Please refer to the specified installation steps in the installation drawings.
1. Fix the condensation strip under the work surface of cabinet. Please ensure the condensation strip is line with
the edge of the work surface. (Step 2)
2. Connect the inlet hose to the cold water supply.
3. Connect the drain hose.
4. Connect the power cord.
5. Place the dishwasher into position. (Step 4)
6. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the Philips
screw in the middle of the base of dishwasher use a Philips screw. To adjust the front feet, use a flat screw
driver and turn the front feet until the dishwasher is level. (Step 5 to Step 6)
7. Install the furniture door to the outer door of the dishwasher. (Step 7 to Step 10)
8. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left
and right door springs. Failure to do this could cause damage to your dishwasher. (Step 11)
9. The dishwasher must be secured in place. There are two ways to do this:
A: Normal work surface: Put the installation hook into the slot of the side plane and secure it to the work
surface with the wood screws.
B. Marble or granite work top: Fix the side with Screw.
1. Take away the four short screws
2.Pin up the four long screws
Summary of Contents for WD431M
