17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
6.4 Delete a Phonebook Entry
1. From the home screen, press Menu.
2. Press OK to select
PHONEBOOK
.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to select
DELETE
and then
press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry you wish
to delete and then press OK.
•
CONFIRM?
is displayed.
5. Press OK again to confirm the delete.
• A confirmation tone is played.
6.
Press Phone Off to return to standby mode.
6.5 Delete All Entries from the Phonebook List
1. From the home screen, press Menu.
2. Press OK to select
PHONEBOOK
.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to select
DELETE ALL
and
then press OK to select.
•
CONFIRM?
is displayed.
4. Press OK to confirm the delete.
• A confirmation tone is played.
5.
Press Phone Off to return to standby mode.
If you have subscribed to the Calling Line Identification (CID) service with your
network service provider, the phone number of your caller will appear on the
handset display when there is an incoming call and in your
Call Log
afterwards.
If the caller’s number is stored in your phonebook along with a name, the name
will appear on the handset display when the call is received and in the
Call Log.
Note:
If the call is from someone whose number is unavailable (e.g. an international
call or from a private exchange), the handset will display
UNAVAILABLE
when
you receive the call and in the
Call Log
afterwards.
If the call is from someone whose number is withheld (e.g. by dialing 141), the
handset will display
PRIVATE
when you receive the call and in the
Call Log
afterwards.
If you have not subscribed to the Caller Line Identification service, the handset
will display
UNKNOWN
when you receive the call, and it will not be saved in the
Call Log
.
Information about incoming calls varies by country and network operators.
7
CALLER DISPLAY (NETWORK DEPENDENT)
You can set the phone to detect up to 5 digits at the start of number and replace
it with another number of up to 10 digits when dialling out.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
AUTO PREFIX
and
then press OK to select.
4. Press Menu to select
DETECT DIGIT
, and then enter the number (up to 5
digits) you want to be detected and press Menu to confirm.
5. Press DOWN / - / PHONEBOOK to show
PREFIX NB
. and press Menu to select.
6. Enter the number (up to 10 digits) you want to replace the Detect Digits, and
press Menu to confirm.
7. Press Phone Off to return to standby mode.
11.6 Auto Prefix
Note:
The default Master PIN is
0000
.
5. Press UP / + / CID or DOWN / - / PHONEBOOK to show the handset
number to un-register and then press OK to confirm or press Phone Off to
cancel the un-registration procedure.
• A confirmation tone is played to indicate successful un-registration.
The Master PIN is used for registration/un-registration of handsets. The default
Master PIN number is
0000
. The maximum length of the Master PIN is 4 digits.
Note:
If you forget your PIN code, you can reset it to its default
0000
using a
handset
Reset
. (
See
Reset the Unit
)
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to select
CHANGE PIN
.
4. Enter the current Master PIN and then press OK to confirm.
• The PIN will be shown as asterisks (*) on the screen as you enter them.
5. Enter your new PIN and then press OK to confirm.
• A confirmation tone is played.
11.4 Change the Master PIN
You can personalise your handset by changing the name that appears on the
standby screen from HANDSET.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
PERSONAL SET
and then press OK to select.
3. Press OK to select
HANDSET NAME
.
• The current handset name is displayed.
4. Press Back to delete letters and digits keys to enter the new name
(maximum 10 characters).
5. Press OK to confirm.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
10.4 Rename the Handset
You can change the display language on your handset. The default setting is
ENGLISH
.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
PERSONAL SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
LANGUAGE
and
then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select your preferred
language and then press OK to confirm.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
Note: Once the display language is set, the handset will switch to display in the
selected language immediately.
10.5 Set the Display Language
Note:
Press and hold # to switch the ringer
On
and
Off
when the handset is in
standby mode. The ringer off icon displays on the screen when ringer off feature
is activated.
The handset emits a tone with each key press. You can choose to turn this tone
on or off. The default setting is
ON
.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
PERSONAL SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
HANDSET TONE
and then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to show
KEY BEEP
and
then press OK to select.
5. Press UP / + / CID or DOWN / - / PHONEBOOK to select
ON
or
OFF
and
then press OK to confirm.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
10.3 Set the Key Beep
You can select from 10 ringer melodies for external calls. (Intercom calls use a
fixed melody)
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
PERSONAL SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
HANDSET TONE
and then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to
RING TONES
and then
press OK to select.
5. Press UP / + / CID or DOWN / - / PHONEBOOK to select the desired melody
from 1 to 10 (each melody will play as it is selected) and then press OK to
confirm.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
10.2 Set the Ring Tone
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
HANDSET TONE
and then press OK to select.
4. Press OK again to select
RING VOLUME
.
5. Press UP / + / CID or DOWN / - / PHONEBOOK to select the desired setting
(each volume level will play as it is selected) and then press OK to confirm.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
9.2.1 Set the Alarm Tone
You can select from 3 alarm melodies.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
CLOCK&ALARM
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ALARM TONE
and
then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select the desired alarm
tone (each tone will sound as it is selected) and then press OK to confirm.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
6.3 Modify a Phonebook Entry
1. From the home screen, press Menu.
2. Press OK to select
PHONEBOOK
.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to select
EDIT ENTRY
and
then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry you wish
to modify and then press OK.
• The current name is displayed.
5. Edit the name using the keypad and pressing Back to delete characters.
6. Press OK to confirm the name.
7. Edit the number and then press OK to confirm the changes.
• A confirmation tone is played.
8.
Press Phone Off to return to standby mode.
6.2 Access the Phonebook
1. From the home screen, press DOWN / - / PHONEBOOK to open the
phonebook list.
Alternatively, from the home screen, you can press
Menu
to show
PHONEBOOK
, press OK then press
DOWN / - / PHONEBOOK
to select
LIST
and press OK to open the phonebook list.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to scroll through the list of
entries
• The phonebook entries are listed in alphabetical order.
3. Press OK to view the details of the selected entry.
4. Press Phone Off to return to standby mode.
Note:
Instead of pressing
UP / + / CID or DOWN / - / PHONEBOOK
to browse the
phonebook entries, you can press the numeric key corresponding to the first
letter of the entry you wish to locate.
For example, pressing Number 2 key will show the first entry starting with A.
Pressing Number 2 key again will show the first entry starting with B, and so
on..., and then press UP / + / CID or DOWN / - / PHONEBOOK, if necessary, to
find the entry you want.
The time, when viewing caller id or setting an alarm, can be displayed either as
12-hour or 24-hour. The default setting is
24 HOURS.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
CLOCK&ALARM
and then OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
SET FORMAT
and
then press OK to select.
4. Press OK again to select
TIME FORMAT
.
• The current setting is displayed.
5. Press UP / + / CID or DOWN / - / PHONEBOOK to select
12 HOURS
or
24
HOURS
and then press OK to confirm.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
9.1.1 Change the Time Format
The date, when viewing caller id, can be displayed either as Month/Day or
Day/Month. The default setting is Day/Month,
DD/MM
.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
CLOCK&ALARM
and then OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
SET FORMAT
and
then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to show
DATE FORMAT
and then press OK to select.
• The current setting is displayed.
5. Press UP / + / CID or DOWN / - / PHONEBOOK to show
DD/MM
or
MM/DD
and then press OK to confirm.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
9.1.2 Change the Date Format
9
CLOCK AND ALARM SETTINGS
9.1 Date and Time Settings
If you have subscribed to the
Calling Line Identification (CID)
service, the time
and date settings will be automatically updated by the network when you receive
an incoming call.
You can also set the date and time manually.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to select
CLOCK&ALARM
and then OK to select.
3. Press OK again to select
DATE/TIME
.
• The last stored date is displayed.
4. Enter the current date and press OK to confirm. The date must be entered in
the format YY/MM/DD, e.g.
enter 03 May 2012 as [1], [2], [0], [5], [0], [3].
5. Enter the current time and press OK to confirm. The default time format is
24
HOURS
. (
To change the time format, see
Change the Time Format
)
For 24-hour format, enter 1:30pm as [1], [3], [3], [0].
For 12-hour format, enter 1:30 am or pm as [0],[1],[3],[0] and then press
UP / + / CID or DOWN / - / PHONEBOOK
to select
AM
or
PM
.
• A confirmation tone is played.
6. Press Phone Off to return to standby mode.
1. From the home screen, press Redial.
2. Press Menu.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to select
DELETE ALL
and
then press OK to select.
•
CONFIRM?
is displayed.
4. Press OK again to confirm the delete.
• A confirmation tone played.
8.5 Delete All Entries from the Redial List
8.4 Delete a Redial Number
1. From the home screen, press Redial.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry and then
press Menu.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to select
DELETE
and then
press OK to select.
•
CONFIRM?
is displayed.
4. Press OK again to confirm the delete.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
The
Call Log
stores the last 10 different external calls, whether or not you have
answered the call.
When there is a new call in the call log, the handset shows NEW CALL or NEW
CALLS, until all have been viewed.
Each handset has its own Call Log and new calls must be cleared independently
on each handset.
Only the most recent call is saved if there are repeat calls from the same number.
When the
Call Log
is full, the next new call will replace the oldest entry. (Note: if
VOICEMAIL is one of the entries, it will not be replaced in the list, but will have
to be deleted manually.)
7.1 Call Log
7.1.1 Access the Call Log
1. From the home screen, press UP / + / CID.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to browse through the call list.
• The calls are displayed in chronological order with the most recent call at
the top of the list.
3. Press OK to see more details of the call. Each press will step through the
Name, Number and Date/Time, if available.
7.1.2 Save a Call Log Entry into the Phonebook
1. From the home screen, press UP / + / CID.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry and then
press OK.
3. Press OK to select
SAVE NUMBER
.
4. Enter the name of the contact (maximum 12 characters) and then press OK
to save the entry to the phonebook.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
7.1.3 Delete a Call Log Entry
1. From the home screen, press UP / + / CID.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry and then
press Menu.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to
DELETE
and then press
OK to select.
•
CONFIRM?
is displayed.
4. Press OK again to confirm the delete.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
1. From the home screen, press Redial.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry and then
press OK.
3. Press Menu and press UP / + / CID or DOWN / - / PHONEBOOK to select
EDIT ENTRY
and then press OK to select.
4. Edit the number and press OK to confirm.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
8.3 Edit a Redial Number
7.1.4 Delete All Entries in the Call Log
1. From the home screen, press UP / + / CID.
2. Press Menu.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to
DELETE ALL
and then
press OK to select.
•
CONFIRM?
is displayed.
4. Press OK again to delete all entries.
• A confirmation tone is played.
1. From the home screen, press Redial.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to browse the redial list.
• The last dialled number will appear first in the redial list.
• If the name is displayed or the number is more than 12 digits, press OK to
see the other digits.
8.1 Access the Redial List
1. From the home screen, press Redial.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to select an entry and press
Menu.
3. Press OK to select
SAVE NUMBER
.
4. Press OK, then enter the name for the contact (maximum 12 characters) and
then press OK to save.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
8.2 Save a Redial Number into the Phonebook
The redial list stores the last 5 numbers dialled. A maximum of 24 digits can be
displayed for each entry.
If you have stored a name in the phonebook to go with the number, the name
will be displayed instead.
8
REDIAL LIST
11.2 Register Additional Handsets
11
ADVANCED SETTINGS
11.1 Handset Registration
IMPORTANT:
When you purchase your phone system, all handsets are already
registered to your base, so you do not need to register them.
Handset registration is only necessary when you buy extra handsets or if a
handset has become faulty.
You can register up to four handsets to one base station, with each handset’s
number (1 to 4) shown on its display.
Note:
Each handset can only be registered to one base.
You need to enter the Master PIN before you can register or un-register
handsets. The default Master PIN is 0000.
1. Press and hold the (page key) on the underside of the base unit for at
least 5 seconds.
• There is no indicator but the base stays in registration mode for about 1
minute.
2. On the handset, press Menu.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to show
REGISTRATION
and then press OK to select.
5. Enter the Master PIN and then press OK to confirm.
12 TROUBLESHOOTING
ALWAYS check that:
• You have followed all the steps listed in the user guide to install and set up
your telephone.
• All connectors are securely inserted into their sockets.
• Mains power for the base unit is switched on at the socket.
• The handset’s batteries are correctly and securely installed and are
sufficiently charged.
“I try to recharge the batteries but I still get a warning that they are low”
• You need to replace the batteries. Dispose of used batteries safely –
do not burn, immerse them in water, disassemble, or puncture the batteries.
• Do not use non-rechargeable batteries in your handset – they may explode,
causing damage.
Registration
“I am not able to register another handset”
• The maximum number of 4 handsets has been reached. You will need to
un-register a handset in order to register a new one.
If the fault persists...
• Disconnect all other instruments connected to the same line and try to make
a call.
• Disconnect the base unit from the telephone line and plug a different phone
into the master telephone socket. Try making a call. If this works, the line is
OK.
• If the call does not work, and you are using a two-way socket adapter,
remove it and plug a telephone directly into the socket.
• If the call now works, the adapter may be faulty.
• If you cannot make a call, the fault may be on the exchange line.
Contact the service provider.
13 DECLARATION OF CONFORMITY
complies with the essential protection requirements of R&TTE Directive
1999/5/EC on the approximation of the laws of the Member States relating to
Radio Spectrum Matters
, the Council Directive 2004/108/EC on the approxi-
mation of the laws of the Member States relating to
Electromagnetic
Compatibility (EMC)
and the European Community Directive 2006/95/EC
relating to
Electrical Safety
.
Assessment of compliance of the product with the requirements relating to the
essential requirements according to Article 3 R&TTE was based on Annex III of
the Directive 1999/5/EC and the following standard:
Manufacturer / Importer
(signature of authorized person)
17 Mar 2014
Date
.....................
We the manufacturer / Importer:
Binatone Electronics International Limited
Floor 23A, 9 Des Voeux Road West, Hong Kong
Tel: (852) 2802 7388 Fax: (852) 2802 8138
Declare under our sole responsibility that the following product
Type of equipment:
Digital Cordless Telephone
Country of Origin:
China
Brand:
Tesco
Model Name:
AWB001 Cordless Phone
series
Signature
..................
Radio Spectrum:
EN 301406: V2.1.1 (2009-07);
EMC:
EN 301489-6:V1.3.1 (2008-08);
EN61000-3-2:2006 +A1 +A2:2009
EN61000-3-3:2008
EN 301489-1:V1.9.2 (2011-09);
EN55022:2010
EN55024:2010
EN 60950-1:2006 + A11+A1+A12:2011
EN50360:2001 + A1:2012 & EN50385 : 2002
Implementing regulation EC1275/2008
Heath & Electrical Safety:
ErP:
“My call was cut off when I went out of range. Now I can’t use my
handset.”
• Move the handset closer to the base unit before you try to make a call again.
“There is interference and noise on the line”
• Move the handset closer to the base unit, or to a different position.
• Try moving the base unit away from other electrical equipment, such as a
television or a computer.
• You’ll get the best reception if you place the base unit as high as possible.
For example, in a two-floor building, the first-floor landing is an ideal place.
“I hear ‘beeps’ from my handset while I’m on a call”
• You may be moving out of range of the base unit. Move closer or your call
may be cut off.
• Check the Battery Level symbol on the display. If it’s low, recharge the
batteries.
“The Caller Display feature isn’t working”
• You need to subscribe to the Caller Line Identification service from your
network service provider.
• The caller may have withheld their number by dialing 141. Or they may be
calling from a network that does not transmit the caller’s number (e.g. if they
are making international calls.)
“When I try to make a call, I hear busy tone”
• If you’re using a multi-handset system, check whether another handset is
already on a call.
“The volume in the earpiece is low when I’m on a call”
• Make sure you’re holding the earpiece correctly over your ear.
• Adjust the volume using
+
.
“I cannot store a phonebook entry”
• The maximum number of 50 phonebook entries has been reached. You
must delete existing entries to make space for new ones.
Intercom and transfer
“I can’t transfer a call”
• Make sure that the other handset is in range of the base unit.
• Make sure that you have entered the correct number for the other handset.
Batteries
“The handset’s battery cells are running low within an hour or two”
• Before you first use the handset, you must leave it to charge on the base
unit or charging pod for at least 15 hours.
• You may need to replace the batteries.
• Check the connection between the base unit and the mains power socket.
10 PERSONAL SETTINGS
Your phone comes with a selection of settings that you can change to
personalise your phone to the way you like it to work.
10.1 Set the Ring Volume
You can set the handset ringer volume from Level 1 to Level 5 or turn the ringer off.
Note:
when you set a ring volume level, if you then turn the ringer off with the
# key, and then turn it back on with the # key, the ringer volume will be at volume
level 4.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
PERSONAL SET
and then press OK to select.
This function enables you to end a call automatically by simply placing the
handset back on the base unit or charging pod. By default, the Auto Hang up
feature is
ON
.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
PERSONAL SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
AUTO HANG-UP
and then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select
ON
or
OFF
and
then press OK to confirm.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
10.6 Set Auto Hang-up
You can un-register any handset, including the one you are using.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
UNREGISTER
and
then press OK to select.
4. Enter the Master PIN and then press OK to confirm.
11.3 Un-register your Handset
Note:
The default Master PIN is 0000.
•
WAITING
flashes on the screen.
• A confirmation tone is played to indicate successful registration, and the
handset will return to standby mode, with its handset number displayed.
• If no base is found with the entered PIN, error tones are played to indicate
failed registration and the handset returns to standby mode. You will need
to repeat from step 1 above.
You may need to press RECALL (R) to send a Recall signal (also called Flash
or Timed Break Recall) for some network services. You should normally leave
the Recall Time at its default setting,
Short (100ms)
, as this is the standard
recall for the UK telephone network. However, it can be changed to Medium
(270ms) or Long (600ms) if your telephone is connected to a private exchange
that requires a different recall time.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
RECALL TIME
and
then press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select
SHORT, MEDIUM
or
LONG
and then press OK to confirm.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
11.5 Change the Recall Time
If you have subscribed to the Caller Line Identification service and do not wish to
hear the phone ring before the caller identification is displayed, you can set the
FIRST RING
to
OFF
.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to
FIRST RING
and then
press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to select
ON
or
OFF
and
then press OK to confirm.
• A confirmation tone is played.
5. Press Phone Off to return to standby mode.
11.7 Set the First Ring
You can reset your phone to its default settings with this feature.
Note:
Upon reset, all your personal settings, call log and redial list entries will be
deleted and the phone will return to its default settings. However, your
phonebook will remain unchanged after a reset.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ADVANCED SET
and then press Ok to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
RESET
and then
press OK to select.
4. Press OK again to confirm.
• A confirmation tone is played and the unit is reset to its default settings.
11.8 Reset the Unit
Everyday use
“I cannot make or answer calls”
• If the handset’s display is blank, it may have been switched off.
Press and hold Power Off key to switch it back on.
• Check that the base unit’s mains power adapter is plugged in and power is
switched on. The base unit needs mains power for normal operation of the
phone – not just for charging the batteries.
• Make sure that you are using the telephone line cable supplied with your
phone. Other telephone line cables might not work.
• Move the handset closer to the base unit.
• Check the Battery Level symbol on the display. If it is low, put the handset
back on the base unit or charging pod to recharge the batteries.
• Switch off the power at the mains socket, wait for a short while and then
switch it back on. This may solve the problem.
“I cannot make calls”
• If the handset display shows KEYS LOCKED, press and hold
*
key to
unlock it before you make a call.
• Only one handset can be connected to an external line at a time. If the
handset displays LINE IN USE , the base is already being used by
another handset, or another telephone is using the line.
“When I press on the keys, nothing happens”
• Make sure that the batteries are fitted in your handset. If the Battery Level
symbol on the display shows ‘low’, put your handset back on the base unit or
charging pod to charge.
“When I key in a number, it appears on the display, but I cannot make an
external call”
• Try a different position for the base unit – somewhere higher if possible or
further away from other electrical equipment.
“The phone does not ring”
• Check that the base unit’s mains power adapter is plugged in and power is
switched on.
• The base unit needs mains power for normal operation of the phone – not
just for charging the batteries.
• Make sure that you are using the telephone line cable that was supplied with
your phone.
• Make sure that the ringer volume settings are not set to off. Increase the
ringer volume settings. (
See
Set the Ring Volume
)
An alarm can be set on a handset, to sound at a set time only once or repeated
each day.
When an alarm is set, the alarm icon is shown on the handset display.
When the alarm time is reached, the handset will flash -ALARM- on the display
and sound an alarm for 1 minute at a fixed volume.
When the alarm rings, you can press any key on the handset to stop the ringing,
even if the key lock is activated.
1. From the home screen, press Menu.
2. Press UP / + / CID or DOWN / - / PHONEBOOK to show
CLOCK&ALARM
and then press OK to select.
3. Press UP / + / CID or DOWN / - / PHONEBOOK to show
ALARM
and then
press OK to select.
4. Press UP / + / CID or DOWN / - / PHONEBOOK to show your required alarm option.
OFF:
Turn alarm off
ON ONCE:
The alarm sounds once at the set time.
ON DAILY:
The alarm sounds daily at the set time.
5. Press OK to select the displayed option.
6. If
ON ONCE
or
ON DAILY
is selected, enter the desired hour and minutes.
Press UP / + / CID or DOWN / - / PHONEBOOK to select
AM
or
PM
if the
time is in 12-hour format.
7. Press OK to confirm the alarm setting.
• A confirmation tone is played.
8. Press Phone Off to return to standby mode.
9.2 Alarm Settings
NOTE:
In compliance with Directive 2002/96/EC, when you purchase a product
that comes with the symbol shown on the right, you are required to dispose of
electrical and electronic equipment by separate waste collection
and you cannot dispose of the product as normal waste.
This equipment and all its components, subsystems and
consumable materials form an integral part of this product
and when you decide to dispose of them you have to take
them to a local recycling centre for appropriate waste disposal,
in compliance with the current regulations.
Details about the location of these centres can be obtained
from your local authority.
Notes for battery disposal
Your product contains batteries covered by the European Directive 2006/66/EC,
which must not be disposed of with normal household waste.
Please be aware of the local rules on separate collection of batteries. The
correct disposal of batteries helps protect the environment and prevent health
hazards.