Chisel Scaler SC 29 PG
Operation & Maintenance Guide
(For 12.7mm A/F Square body and releasing slot at back type Chisel)
OPERATION:
Chisel Scalers are rugged, dependable tools designed to give years of satisfactory service. Follow the instructions
mentioned here to enhance the life and performance of your scaler.
DAILY BEFORE OPERATION:
Disconnect and pour in 1 to 2 ounces of recommended oil into the tool and reconnect hose blowing out any
accumulated dirt in the hose line before connecting.
LUBRICATION REQUIREMENT:
Always install a line lubricator on the air line as close to the tool as possible. A filter regulator lubricator unit
(FRL) is strongly recommended. Keep the lubricator bowl topped up with oil and check that the oil is reaching the
tool. Running without lubrication is likely to cause damage the components causing premature replacement.
AIR SUPPLY:
The Scalers work best at 5 to 7 bar pressure. The air should be clean, dry and lubricated. Install a FRL unit as
close to the tool as operation will allow.
RECOMMENDED LUBRICANTS:
ABOVE 27
0
C 80
0
F
5
0
C-27
0
C 40
0
F-80
0
F
BELOW 5
0
C 40
0
F
SHELL
Toona R. 72
Toona R. 41
Toona R.27
MOBIL
Almo 529
Almo 527
Almo 525
ESSO
Arox.EP.65
Arox EP.45
CALTEX
Rando Oil 150
Rando Oil 100
Rando Oil 46
CP
Airolene Tool Oil
TEXACO
Regal oil F (R&O)
Regal Oil PE (R&O)
Regal Oil B (R&O)
DALTRON
Silkolene 881
Silkolene 548/T
Silkolene 773
BURMAH CASTROL
Castrol RD Oil 3
Castrol Rd Oil Light
Magna SPX
BP POWER
PETROLEUM
RD220 HP60-C
RD150 HP20-C
RD80 HP10-C
DUCKHAM
Garnet 7
Garnet 6
Zero Fio 5
STERNOL
Merlin 87
Merlin 71
Merlin 54
PETROFINA
Purifoc 53
Purifoc 46
Purifoc 32
CHEVRON
Vistac Oil 18X
Vistac Oil 19X
Vistac Oil 9X
IOC
Servoneum 100
-----
-----
HP
Numatic 100
-----
-----
FF - MM - 108 REV - 1
Sheet 2 of 5
TO CHANGE CHISEL:
Rotate ring (07) in such a way so that hole on the ring exactly match with steel ball (09). when chisel (10) is
pulled out, the steel ball (09) will be lifted up and chisel will come out. Push another chisel having 12.7mm A/F
square body and slot at back. After the slot has crossed the steel ball (09), again rotate ring (07) so that steel ball
(09) is completely pressed in.
INTENDED USE
Sr. No.
Model No.
Capacity in BPM
Chisel Size
1
SC 24 PG
3000
7” Long, 19mm Wide 93/4)
2
SC 24 ST
3000
7” Long, 19mm Wide 93/4)
3
SC 29 PG
2200
7” Long, 19mm Wide 93/4)
4
LR 076
2250
5/8” Hex 4” Blade
5
LR 116
2250
5/8” Hex 4” Blade
6
LR 146
2250
5/8” Hex 4” Blade
7
LR 176
2250
5/8” Hex 4” Blade
