Terrco 3100-3P Operating Instructions Manual Download Page 7

E. To Start the 3100 LP Propane     
     Engine 
     1. A 33 lb. special combination vertical-
horizontal propane cylinder liquid withdrawal 
Model No. TU33L, must be used on this       
machine fitted with a Rego #7141 male fitting.  
The Terrco

® 

3100LP operates on the liquid 

principle. 
     2. When installing tanks, the bottom guide 
hole near the top of the cylinder must drop over 
the locating pin on the cylinder bracket of the 
handle. Connect quick coupler to the cylinder.  
DO NOT USE A WRENCH - only hand tight-
en. 
     3. You are now ready to open main gas 
valve in fuel tank.  CAUTION - “SLOWLY” 
open main gas valve in the fuel tank.  An abrupt 
full opening of the valve will induce dirt from 
within the tank to enter the fuel line.  Too rapid 
an opening can also cause frost to form on the 
fuel filter, main valve, and inlet line.  CHECK 
FOR GAS LEAKS WITH SOAP SUDS       
SOLUTION.  THERE MUST BE NO LEAK. 
     4. Check oil level of crankcase. 
     5. Make certain clutch is disengaged. 
     6. Place weights in the “up” position. 
     7. Attach battery cables from starter to the 
battery. 
     8. Pull throttle knob a quarter to half way 
out. 
     9. Pull out ignition switch to “on” position 
and press rubber start button to start. 
     10. Allow engine to warm up approximately 
10 minutes. 

     11. After a few minutes of warm-up and 
with weights in the upper weight baskets, pull 
throttle lever out to full open position, apply 
weight on the handle to relieve pressure on 
stones and engage clutch (pull clutch handle 
towards you). 
NOTE:  We recommend that for the first eight 
hours the machine be operated with the weights 
in the upper weight baskets to allow engine to 
break in without undue load factor. 
     12. After the initial eight hour engine break 
in period, we suggest that on all future opera-
tions, that you make your first “rough” grind 
operation with the weights in the upper weight 
baskets.  You can then lower the weights to the 
lower weight baskets for the remaining portion 
of the rough grinding operation. 
     13. There may be excessive oil consumption 
during the first 10 days of operation during the 
break in period.  If oil consumption is over 1 
quart per day, contact you local AUTHORIZED 
WISCONSIN repair station. 
     14. CAUTION Do not operate Terrco

® 

Starting the 3100LP  

Summary of Contents for 3100-3P


















Reviews: