ADVISORY
The Terra CA Series loudspeakers are designed for installation in walls or ceilings. If
you are not completely comfortable
completely comfortable with cutting holes in your walls and fishing speaker
wires through your walls, please hire a professional audio/video contractor. The follow-
ing instructions assume that you are installing into existing wallboard.
AMPLIFIER POWER
Speaker damage most commonly results from UNDERPOWERING the speaker. If you
hear distortion from the speaker, chances are that the amplifier has exceeded its output
capability and is “clipping.” If you hear distortion at loud levels, turn down your amp
immediately! Clipping WILL cause damage to a speaker, and such damage is not cov-
ered under the warranty.
THE “BREAK-IN” PERIOD
You may play your Terra speakers immediately with excellent results. However, subtle
improvement can be expected as the ACAD™ drivers break in after 50 to 100 hours
of operation.
PAINTING
The speaker frame and the grille can be painted with a thin coat of spray paint.
• Use a thin, flat-blade screwdriver to gently pry up the grille from all sides until you
can grasp it for removal. Take care not to damage the frame as you pry.
• Applying too much paint to the grille can plug the holes.
• Mask the speaker assembly so only its frame gets painted.
• Allow paint to dry thoroughly before handling the speaker.
SPEAKER LOCATION
The diagram below provides placement guidelines for installation in walls. For ceiling
installations the spacing between speakers and from corners is the same.
TERRA CA SERIES
OWNER’S GUIDE FOR ALL CA SERIES SPEAKER MODELS
Custom Audio Manufacturing of Maine (CAMM, Inc.), 228 Old Portland Rd., Suite #4, Brunswick, Maine 04011
tel 207.725.1005
•
e-mail: [email protected]
•
www.terraspeakers.com
STEREO SOUND COVERAGE USING CA.10WF ALONE OR WITH A PAIR OF CA.10
rev2007_02
������������
������������
������������
������������
������������
�����
����
�������
�������
�����
�����
STEP 1: MARK SPEAKER LOCATIONS
are not sure about the location of the studs, purchase an inexpensive “stud finder,” a
magnetic device that indicates stud position by detecting nails.) Try to locate the speak-
ers at least 18" from corners.
Be careful not to locate the speakers too close to electrical switches, outlets, phone
jacks, and ceiling fixtures so as to avoid cutting into their wiring.
Using a level, mark a straight line on the wall or ceiling to denote the bottom edge of
each speaker. Using the supplied cardboard template that is part of this package, trace
the outline of the speaker cutout using the lines you’ve drawn as a reference.
STEP 2: CUT THE HOLES
You will need a utility knife or small saw, and a drill with a 1/4- to 1/2-inch-diameter
bit. Drill holes on the inside corners of the outlines you’ve traced. These holes make it
easier to begin cutting or sawing. Then cut or saw exactly along the paths you’ve traced.
Remove the pieces you’ve cut as well as any insulation that will impede installation.
STEP 3: RUN THE SPEAKER WIRING
Use at least 16-gauge wire. For long runs (100 feet or more) we recommend thicker
14-gauge wire. Run the wiring to the connection point. Leave at least 12 inches at the
cutout for connecting each speaker.
STEP 4: CONNECT THE SPEAKER WIRES
Solder the wire leads to the positive (red) and negative terminals on the speakers. Note
that the R2, S2 and WF models also provide spring clip terminals.
STEP 5: INSTALL THE SPEAKERS (SEE DIAGRAMS BELOW)
Remove the grille to gain access to the mounting screws. Make sure the clamping tabs
on the back of the speaker are in a vertical position, then tilt the speaker assembly
slightly to work it into the hole. DO NOT TIGHTEN THE SCREWS YET.
Tighten the front-panel screws while making sure each speaker is positioned squarely.
TIGHTEN ONLY UNTIL YOU FEEL SOME RESISTANCE. The clamping tabs will rotate into
position and draw the frame in against the wallboard, securing the speaker in place. The
speaker frame is flexible, so it will conform to slight variations in the flatness of the wall.
DO NOT OVERTIGHTEN or you may damage the frame.
STEP 6: RE-ATTACH THE GRILLES
Gently press around the perimeter of the grille to work it back into the frame.
��������
�����
�������
���
����
���
����
�������
Start with clamping tabs in
VERTICAL position.
After positioning the speaker, turn the
front-panel screws to draw the clamping
tabs snug against the wallboard.
BACK
FRONT
INSTALLATION
CUTOUT DIMENSIONS
Templates are supplied
CA.10.1S
inch: 5-5/8 x 5-5/8 x 3-1/2
mm: 144 x 144 x 88
CA.10.2S
inch: 5-5/8 x 5-5/8 x 3-1/2
mm: 144 x 144 x 88
CA.WF10.2S
inch: 5-5/8 x 5-5/8 x 3-1/2
mm: 144 x 144 x 88
CA.10.1R
inch: 6-1/2 diameter
mm: 165 diameter
CA.10.2R
inch: 6-1/2 diameter
mm: 165 diameter
CA.WF10.2R
inch: 6-1/2 diameter
mm: 165 diameter
