•
Technical faults must be reported immediately to
the person responsible for supervising the bin lift.
The bin lift must be taken out of service until the
fault has been rectified (if this may be dangerous).
•
Never use the lifting chair or other parts of the
bin lift system as a seat,
this is extremely dange-
rous!
•
Under no circumstances may the controls be
changed.
•
Under no circumstances may any of the safety
provisions fitted be removed or changed.
•
Don’t blind off or cover the ultrasonic sensors, fit-
ted in the safety arms, under any circumstances.
•
If the safety provisions are damaged they must be
repaired or replaced immediately by original parts.
•
Under no circumstances may the cycle speeds and
lifting forces set by the manufacturer be changed.
•
Operating and safety decals must be present and
properly legible.
•
Actions that override the safety provisions are
expressly forbidden!
•
Reversing is only permitted when the lifting chairs
are at a safe height.
•
It is prohibited to stand on the footboards while
the refuse collection vehicle is reversing.
•
Make sure that you are visible to the driver of the
refuse collection vehicle while it is reversing.
•
Check the lights in the controls daily, faulty lights
must be replaced as soon as possible.
•
The bin lift may never be used as a hoisting instru-
ment.
•
Vehicles must not be towed by attaching the
towing cable to the bin lift.
•
The refuse collection vehicle may never be lifted
by the lifting points of the bin lift.
•
The lifting chairs must be at transport height while
driving.
•
When riding on the vehicle you must absolutely
not sit or stand on parts of the machine other
than the special footboards for this purpose,
this
really is extremely dangerous!
•
It is not wise to work with the bin lift in extreme-
ly bad weather conditions (storm, thunderstorm,
etc.).
6
EN
E
N
2
.
S
af
e
ty
37679
05-2017
2.1
General safety instructions
ã
Terberg Machines B.V., IJsselstein, The Netherlands
All rights reserved. No part of this book may be reproduced, stored in database or retrieval system, or published, in any form or in any
way, electronically, mechanically, by print, photoprint, microfilm or any other means without prior written permission from the publisher.
Terms of conformity
This bin lift conforms to the current standards at the
time of production. It has been tested and checked,
on a rig, in normal conditions with an increase of
25% weight in static and 10% weight in dynamic
operation.
It is the end user’s responsibility to maintain the
equipment in accordance with the manufacturer’s
recommendations, also if there is a risk of damages
or injury the bin lift must be taken out of service
immediately.
General
•
The bin lift may never be operated when the refu-
se collection vehicle is travelling along and also not
with reverse gear engaged.
•
The bin lift may only be operated by persons who
are familiar with the operation of the bin lift.
•
First read the operating instructions before you
start using the bin lift.
•
Read through the operating instructions for the
compaction body carefully.
•
In your daily work as bin lift operative you are
working in traffic, do not put it or yourself in dan-
ger.
•
Before you start your round agree with your col-
leagues how to proceed in certain situations such
as stopping, driving off, etc.
•
When you are working with the bin lift, you
should not wear any loose clothing and jewellery.
•
When working always wear work clothing, safety
footwear and work gloves that comply with the
standards indicated in the table below.
•
Make sure that an unattended bin lift can never be
put into operation by unauthorised persons
(remove the ignition key).
•
Do not start using the bin lift in areas or by instal-
lations where due to the presence of gases and/or
flammable substances there is a fire and/or explo-
sion hazard.
•
The bin lift may not be used under any circum-
stances where there is an oil supply of more than
60 litres/minute.
Personal protection
equipment:
According to standard:
Work clothing
NEN-EN-ISO 20471:2013
Safety footwear
NEN-EN-ISO 20345:2011
Work gloves
NEN-EN 420:2003+A1:2009
