background image

OPERATION

7

Tennant 1140 (03--04)

MACHINE SETUP

1. Carefully check carton for signs of damage. Report

damages at once to carrier. The machine is shipped

fully assembled and is ready for use.

2. Unscrew and remove solution tank lid. Using a hose

or bucket, fill tank with 57L (15 gal) of hot water,

60

°

C (140

°

F) maximum (Figure 1).

ATTENTION: Use different buckets to fill and drain

machine to prevent solution system clogs.

FIG. 1

WARNING: Do Not Use Flammable Liquids Or

Operate Machine In Or Near Flammable Liquids,

Vapors Or Combustible Dusts.

3. Add a recommended cleaning solution to the

proper dilution ratio.

FOR SAFETY: When using machine, follow mixing

and handling instructions on chemical containers.
ATTENTION: If using powdered cleaning

chemicals, mix chemical with water prior to

adding to the tank.

NOTE:

If desired, water alone achieves excellent

cleaning results.

4. Replace solution tank lid after filling.
5. Connect two 7.6 m (25 ft.) extension power cords

into machine.

6. Plug each extension cord into separate grounded

circuits. Circuit indicator lamp (green) will light

when cords are on separate circuits (Figure 2).

ATTENTION: When plugging extension cords into

receptacles be certain to use separate circuits.

This will prevent a circuit overload. Do not

activate heater if green indicator does not light.
FOR SAFETY: Do not operate machine unless

cords are properly grounded.
FOR SAFETY: Do not operate machine with the

use of additional extension cords. Only use

manufacturer’s extension cord equipped with

machine which has proper capacity and is

grounded.

FIG. 2

7. Attach vacuum and solution hoses to front of

machine, then to floor or hand tool (Figure 3).

FIG. 3

Summary of Contents for 1140 607681





























Reviews: