Tendercare Mini Tilt Wheelchair User Manual Download Page 6

 Mini Tilt Wheelchair 

 

Document No: 054-01 v6 

Page 6 of 28  

January 2014 

Mintilt (newstyle) user manual.doc

 

 
3: Unpacking 
 
The  wheelchair  is  delivered  in  a  cardboard  carton  approximate  weight  20  kg  and  size 
630mm wide x 595mm deep x 890mm high. 
 
Warning  the  transit  carton  is  heavy  so  moving  and  unpacking  must  be  done  with 
care. Observe all lifting and handling regulations. 
 

1.  Stand the carton upright making sure it is supported and cannot fall over. Open the 

carton  and  remove  any  packages  or  packing,  which  could  obstruct  the  removal  of 
the frame. 

 

2.  Carefully pull out the wheelchair and check that you have the following items: 

 

Item 

Component 

QTY. 

Yes 

No 

Mini Tilt Wheelchair 

 

 

Armrests 

 

 

User Manual 

 

 

 
IMPORTANT: 
If any items are damaged or missing, then please contact Tendercare, preferably by 
email  at 

[email protected]

  or  alternatively  please  call  us  on  (01903)  726161 

within 36 hours of delivery. 
 
After  unpacking  and  checking  you  have  all  components  and  they  are  in  good  condition 
dispose of the packaging at your local recycling centre. Alternatively retain and reuse. 
 
4:  Preparing the wheelchair for use 
 
Warning: When assembling the wheelchair for use, ensure that you hold the frame 
so that you avoid any danger of catching your fingers in moving parts. 
 
Keep children clear of the wheelbase during opening and folding. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Mini Tilt Wheelchair





























Reviews: