Tenda FH456 User Manual Download

Page: 24 / 82

Specify Your Internet Settings

Tips

It may take a few seconds to check your static IP info. So please wait for a few seconds, and refer to

the

Connection Status

on the

Status

page.

5 Join Your WiFi

This part instructs you how to connect to your wireless network via your notebook or other wireless

devices. We take

, and

as examples here. Choose the

corresponding configuration steps according to your needs.

Windows 8



Click the icon

on the bottom right corner of your desktop.

Tips

1. If you cannot find the icon

, please move your cursor to the top right corner of your desktop,

select

Settings > Control Panel > Network and Internet > Network and Sharing Center >

Change adapter settings

, right click

Wi-Fi

and select

Connect/Disconnect

2. If you cannot find your WiFi from the list, ensure the Airplane Mode is not enabled on your

Summary of Contents for FH456



















































































Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands

Tenda FH456, User Manual

Search results

Summary of Contents for FH456

Reviews:

Related manuals for FH456

Brands by name

Popular brands