Tempstar FMC4X Service And Maintenance Instructions Download

Page: 8 / 14

A13388

Fig. 10

−

Blower Support Plate Screws

6. Remove the two middle screws above/behind the blower

motor that’s attached to the top plate.

PERSONAL INJURY HAZARD

Failure to follow this caution may result in personal injury.
After removing the sixth and final screw in Step 6, the blower

assembly will be completely disconnected from the unit. Be

ready to lower the blower assembly.

CAUTION

A13389

Fig. 11

−

Remove Middle Screws

E. FPM(A,B)N, FMC4X, FMU4X

−

Servicing the Fan Motor

1. After removing the blower housing from the unit, discon-

nect ground wire from screw on grounding bracket.

A13390

Fig. 12

−

Disconnect Ground Wire

2. Remove grounding bracket from motor

−

mount assembly.

At this point, the clamp brackets will be loose and can be

removed.

A13391

Fig. 13

−

Remove Grounding Bracket

3. Remove capacitor cover.

A13392

Fig. 14

−

Capacitor Cover

Summary of Contents for FMC4X















Search results

Summary of Contents for FMC4X

Reviews:

Related manuals for FMC4X

Brands by name

Popular brands

Tempstar FMC4X, Service And Maintenance Instructions

Search results

Summary of Contents for FMC4X

Reviews:

Related manuals for FMC4X

Brands by name

Popular brands