background image

PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING HEATERS

IMPORTANT: Read all instruc-
tions and warnings carefully
before starting installation.  Fail-
ure to follow these instructions
may result in a possible fire haz-
ard and will void the warranty.

WARNING: If the information in
this manual is not followed ex-
actly, a fire or explosion may
result causing property damage,
personal injury or loss of life.

— Do not store or use gasoline or

other flammable vapors and
liquids in the vicinity of this or
any other appliance.

— What to Do If You Smell Gas

Do not try to light any appli-
ance.

Do not touch any electrical
switch; do not use any phone
in your building.

Immediately call your gas
supplier from a neighbor's
phone. Follow the gas
supplier's instructions.

If you cannot reach your gas
supplier, call the fire depart-
ment.

— Installation and service must be

performed by a qualified in-
staller, service agency or the
gas supplier.

This is an unvented gas-fired
heater. It uses air (oxygen) from
the room in which it is installed.
Provisions for adequate combus-
tion and ventilation air must be
provided. Refer to Page 4.

Vent-Free Gas Fireplaces

Models:
VF36RN, VF36RNH, VF36RP

Homeowner’s Installation and

Operating Instructions

5L24 

410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777

Temco Fireplace Products

Gas Fired
Unvented
Room Heaters

INSTALLER: DO NOT DISCARD THIS MANUAL - Leave in fireplace for homeowner.

Models with “N” after the model number use natural gas;
models with “P” after the model number use Propane
(LP) gas.

78586  11/03  Rev. 8

This appliance is UL Certified under ANSI Standard

Z21.11.2-2000 as an unvented room heater

Summary of Contents for VF36RN

























Reviews: