background image

INSTALLER / CONSUMER 

SAFETY INFORMATION

PLEASE READ THIS MANUAL 
BEFORE INSTALLING AND 
USING APPLIANCE

WARNING! 

IF THE INFORMATION IN THIS 
MANUAL IS NOT FOLLOWED 
EXACTLY, A FIRE OR EXPLO-
SION MAY RESULT CAUSING 
PROPERTY DAMAGE, PERSON-
AL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY
Installation and service must 
be performed by a qualified 
installer, service agency or the 
gas supplier.

WHAT TO DO IF YOU SMELL GAS:

•  Do not try to light any appliance. 
•  Do not touch any electric switch; do not 

use any phone in your building. 

•  Immediately call your gas supplier from 

your neighbor’s phone. Follow the gas 
suppliers instructions. 

•  If you cannot reach your gas supplier 

call the fire department.

DO NOT STORE OR USE GASO-
LINE OR OTHER FLAMMABLE 
VAPORS AND LIQUIDS IN THE 
VICINITY OF THIS OR ANY OTH-
ER APPLIANCE.

WARNING:  Improper installation, ad-
justment, alteration, service or main-
tenance can cause injury or  property 
damage. Refer to this manual. For 
assistance or additional information, 
consult a qualified installer, service 
agency or the gas supplier.

Direct Vent Zero Clearance 
Gas Fireplace Heater

 

Models: 
DV1000N/P, DV1200N/P, DV1400N/P

76657

DV1000/1200/1400

cover

12/2/03  djt

Homeowner’s Installation and 

Operating Manual

C           US

U.S. Patents: 5,669,374; 5,562,088; 6,138,667; 
Can. Patent: 2,139,684

76657  5/08  Rev. 31

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Summary of Contents for DV1000N









































Reviews: