manualshive.com logo in svg

Telit Wireless Solutions WE866E4-P, At Commands Reference Manual

Share
Download
Telit Wireless Solutions WE866E4-P At Commands Reference Manual Download Page 53

WE866E4-P AT Commands Reference Guide

80572ST10887A Rev. 0.0

53

2018-02-16

PRELIMINAR

Y

Response

Table 85, page 53

, describes the responses and remarks for AP Configuration command.

Synchronous Response

Table 86, page 53

, describes the synchronous responses and remarks for AP Configuration 

command.

Hidden SSIDMandatory

Value range: 

0,1

Format:

 Integer

Default value:

 0

It specifies the hidden SSID created for a 
Network, where:
0- disables the hidden SSID and 
1-enables the hidden SSID

Beacon 
Interval

Mandatory

Value range: 

100-1000

Format:

 Integer

Default value:

 100

Unit: 

TUs

It specifies the interval between the beacon 
frames coming from access point. 
It is measured in TUs (Time Units) where, 
One TU is 1024 microseconds.

DTIM 
Period

Mandatory

Value range: 

1-255

Format:

 Integer

Default value:

 3

Unit: 

seconds

DTIM (Delivery Traffic Indication Map) 
depends on the Beacon Interval. 
It specifies that when DTIM enabled 
beacon frame arrives, station wakes up 
with a default period value 3. So for every 
three beacons, connected sleeping stations 
wakes up and receive the beacon frames. 

Table 84   AP Configuration Parameters

Parameters Mandatory/Optional

Value

Description

Table 85   AP Configuration Response

Responses

Remarks

OK

Success.

ERROR

If parameter is not valid.

Table 86   AP Configuration Synchronous Response

Responses

Remarks

OK

Success.

ERROR

If parameter is not valid.

Summary of Contents for WE866E4-P

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands