manualshive.com logo in svg

Telit Wireless Solutions WE866E4-P, At Commands Reference Manual

Share
Download
Telit Wireless Solutions WE866E4-P At Commands Reference Manual Download Page 19

WE866E4-P AT Commands Reference Guide

80572ST10887A Rev. 0.0

19

2018-02-16

PRELIMINAR

Y

4  Architecture

This chapter describes the system architecture of Serial-to-WiFi Application.

•

Working Principle, page 19

•

System Initialization, page 19

4.1  Working Principle

Figure 1, page 19

, representation shows the communication between  WE866E4-P Module 

and the Host:

Figure 1   Communication between the Module and the Host

4.2  System Initialization

During the initialization process, the module SW tries to fetch the configuration file (also 
called as profile) from the file system. If the profile file is not found, it sets the default 
values i.e. factory default values to profile and creates the file in the file system.

As per the default profile, it starts in AP mode initializing the provisioning SW block. User 

can either configure the module through the provisioning mechanism or it can issue 
commands to start in STA mode and join to the intended AP.

Summary of Contents for WE866E4-P

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands