Telit Wireless Solutions EVK Series User Manual Download Page 15

Page: 15 / 49

Telit EVK4

HW User Guide\

0805 Rev. 6

Page

2017-05-19

NOTE:

(*) Is strongly recommended power the EVK4-LE910 V1/V2 product variant
through an USB3.0 port instead of USB2.0 to avoid unexpected reset issues
of the entire system.

Power Consumption

Mode

Average

(mA)

Mode Description

Switched Off

0.095

Module supplied but switched off

Sandalone mode

54.2mA

Full funcionality of the device. xE910

idle

(

GPS enabled, tracking mode)

Sending data mode

494.1mA

xE910 module in Tx/Rx mode. Data

Standalone mode

14.1mA

Full funcionality of the device. xE910

idle

Sending data mode

534.2mA

xE910 module in Tx/Rx mode. Data

(GPS enabled, tracking mode)

Booster pack mode

36.5mA

(Idle, Without SIM)

BoosterPack Mode

36.2mA

(Idle, SIM, SW202/SW203 ON)

BoosterPack Mode

22.3mA

Idle, SIM, SW202/SW203 OFF

BoosterPack Mode

(Running Windows IoT)

91.7mA

Idle, SIM, RPi idle

BoosterPack Mode

(Running Windows IoT)

128.2mA

Idle, SIM, GPS, RPi idle

BoosterPack Mode

(Running Windows IoT)

257.9mA

Idle, SIM, GPS, RPi idle, HDMI-

Display

BoosterPack Mode

MSP-EXP430F5529LP

(Running LED's App)

41.3mA

Idle, SIM,

Launchpad_EXP430F5529LP

BoosterPack Mode

MSP-EXP430F5529LP

(Running LED's App)

81.9mA

Idle, SIM, GPS,

Launchpad_EXP430F5529LP

BoosterPack Mode

MSP-EXP432P401R (Running

LED's App)

110.5mA

Idle, SIM,

Launchpad_EXP432P401R

BoosterPack Mode

MSP-EXP432P401R (Running

LED's App)

157.4mA

(Idle, SIM, GPS,

Launchpad_EXP432P401R

Summary of Contents for EVK Series


















































Search results

Summary of Contents for EVK Series

Reviews:

Telit Wireless Solutions EVK Series, User Manual, Page: 15 / 49

Search results

Summary of Contents for EVK Series

Reviews: