CCD Monochrome
Video Camera
Operation Manual
Model
CS8630BH
BEFORE USE - GENERAL SAFETY
INSTRUCTIONS
This instruction manual contains important information for the
operator (user) and/or people around him/her to avoid personal
injury, or property damage to him/her or people around him/her by
using this product correctly. Prior to use, read this operation
manual carefully to fully understand its instructions for correct
use.
OWNER’S RECORD
Please fill in the blank below the model name and product serial
number, which is found on bottom chassis of your device. Keep
this number for your record.
Serial No.
WARNINGS & CAUTIONS
[Definition of markings]
The meaning of each mark used in this instruction manual is given
below.
DANGER
This mark warns the user that improper use,
indicated with this mark, may cause death or
severe personal injuries against the user or
people around him/her.
CAUTION
This mark warns the user that improper use,
indicated with this mark, may cause personal
injuries (*1) or material damages (*2) against
the user or people around him/her.
Notes
*1 : Personal injuries mean wounds, burns, electric
shocks, and others for which the person injured need
not to be hospitalized nor to be cared for the long
term.
*2 : Material damages mean any direct or consequential
damages related to property or material loss.
This mark indicates what the user
SHOULD NOT
DO
. The details of things which the user should not
do are described next to this mark.
This mark indicates what the user
MUST DO
. The
details of things which the user must do are described
next to this mark.
This mark indicates that the user must be alert against
a possible
DANGER
. The details of the danger which
the user must be aware of are described next to this
mark.
This mark indicates that the user are given a
CAUTION
against possible hazards. The details of
the caution
which the user must be aware of are
described next to this mark.
●
Handling Precautions
DANGER
MUST
If any overheating sign is observed, discontinue
use immediately.
In the event that smoke, smell, or any other
overheating sign is observed, turn its power
switch OFF immediately, and remove its camera
cable from camera connector. Do NOT try to
continue to use your camera. To do so in spite
of a clear sign of a malfunction invites a fire, an
electric shock hazard, or any other serious
damage. In such case, after confirming that there
is no risk of a fire accident, contact us or our
dealer/distributor through which you purchased
this device for repair service. To avoid hazard, do
NEVER attempt to repair it yourself.
MUST
If any malfunctioning sign is observed,
discontinue use immediately.
Do NOT try to use this device when it is
obviously malfunctioning. (Example: No
images on the monitor) In the event of a
malfunction, turn its power switch OFF
immediately, and remove its camera cable from
camera connector. In such case, contact us or our
dealer/distributor through which you purchased
this device for repair service.
MUST
If any liquid gets into the device, discontinue use
immediately.
In the event that water, or any other type of
liquid gets into the body, do NOT try to
continue to use the device. To do so invites a f
ire or an electric shock hazard. In such case,
turn its power switch OFF immediately, and
then remove its camera cable from camera
connector. After that, contact us or our
dealer/distributor through which you purchased
this device for repair service/technical advice.
MUST
Connection/Disconnection only AFTER
power OFF.
When you connect/disconnect camera
connector, make sure to turn power SW OFF
first. This camera is not designed for “hot-
plugging”. Do NEVER make
connection/disconnection while power ON.
Doing so might cause a breakdown.
DANGER
MUST
Use manufacturer-recommended peripheral
devices (option units) only.
Make sure to use option units specified in this
operation manual only. When connected with
any other non-guaranteed peripheral devices,
your camera might fail to perform its full
capacity. In the worst case, it might cause a fire
or breakdown.
NEVER
pull apart
Do NOT disassemble this device.
Do NOT attempt to pull apart, repair, or modify
your camera yourself. To do so might lead to a
fire or an electric shock accident. Contact us or
the dealer/distributor from which you purchased
the device for repair/modification.
DON’T
Do NOT supply any power other than specified.
This device is designed to work only under
specified voltage. Do NOT attempt to supply
the device with power other than specified.
Supplying the device with any unspecified
power invites a fire or an electric shock hazard.
(CS8600 series --- DC+12V)
DON’T
Do NOT use the camera in a high-humidity
environment.
Do NOT place your camera near a humidifier,
or in other high-humidity environment. To do so
might cause a fire or an electric shock accident.
●
Handling Precautions
CAUTION
CAUTION
If the camera is operated in the electromagnetic
field, there may be cases where beat noises
(vertical, horizontal, or oblique stripes) appear in
the video output. In that case, take preventive
measures on the electromagnetic-wave
generating source so that your camera do not
receive the interference by the
electromagnetic-wave. Take extra precautions
against electromagnetic-wave-interference if
your camera is used with a servomotor, inverter,
or other electromagnetic-wave-generating
equipment.
CAUTION
Avoid giving a strong shock against the camera
body. It might cause a breakdown or damage. If
your camera is used in a system where its camera
head is subjected to strong repetitive shocks, its
camera head is possible to break down. If you
intend to use your camera in such a situation,
make sure to use an optional camera-connector
-fixing-hardware to connect the connector-plug
to the camera body.
CAUTION
When the camera is not in use, put a lens or a
lens-cap onto the camera head so that the image
pickup plane of CCD is protected from dust,
foreign object, or any other flaw-causing object.
If the glass plane (image pickup plane) gets dirty,
clean it with a cotton swab. When it needs to be
cleaned with a cleaner, be sure NOT to use any
organic solvent other than ethyl alcohol. As a
countermeasure against condensation, when the
camera is moved from a warm
condition/environment to a cold one, take
appropriate precautions to prevent condensation
from forming on the camera.
CAUTION
Do not pull strongly the camera
cable/camera-head nor swing it. The stress from
pulling or swinging may cause damage in the
coating of the cable, or breaks in the inside
wires.
CAUTION
Avoid short-circuiting signal output. Otherwise,
it may cause a malfunction.
CAUTION
Do NEVER expose its camera head to any
intensive light (such as direct sunlight).
Otherwise, its inner image pickup device might
get damaged.
This equipment has been tested and found to comply with the
limits for a class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in
which case the user will be require to correct the interference at
his own expense.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device accept any
interference received, including interference that may cause
undesired operation.
RESTRICTION FOR USE
In the case where a malfunction of this camera (e.g. video output
cut-off) can be expected to lead to a significant accident, avoid
using this device for such system build-in use.
DISCLAIMER (LIMITED WARRANTY)
We assume no responsibility and shall be held harmless for
damage or loss incurred by the user in the following cases.
1.In the case where damage or loss is caused by fire, earthquake,
or other acts of Gods, acts by a third party, misuse by the user
deliberately or erroneously, or use under extreme operating
conditions.
2.In the case where any indirect, additional, consequential
damages (e.g. loss of expected interest, suspension of business
activities) are incurred as results of a malfunction or
non-functioning of this device, we shall be exempted from
assuming responsibility for such damages.
3.In the case where damage or loss is caused by incorrect use
which is not in line with the instructions given in this
operation manual.
4.In the case where damage or loss is caused by a malfunction
resulting from bad connection with other equipment.
5.In the case where damage or loss is caused by repair or
modification done by the user.
PRODUCT DESCRIPTION
Model CS8630BH is a miniature camera series featuring its
ultra-small light-weight body. The CS8630BH is designed mainly
for factory automation, machine vision, and image measurement
application.
FEATURES
(1) High resolution
The 380,000 pixel CCD realizes the horizontal resolution of
570TV lines.
High-density images with minimum moire-fringes & beatings
are obtained. (CCIR: 440,000 pixels, 560TV lines)
(2) Ultra-compact & light-weight body
The camera features its ultra-small light-weight body. Its super-
small body will free you from much of your space restriction
problem. The camera is driven by DC12V.
(3) Electronic shutter
The built-in electronic shutter allows this camera to
capture a fast-moving object clearly and sharply.
(4) AGC (Automatic Gain Control)
This series is equipped with AGC function. With the
AGC, the camera obtains optimal images constantly
even when the amount of incoming light fluctuates.
(5) Restart/Reset
When the restart/reset function set ON, the camera
captures images at any timing given by R.R. pulse
input (VD input).
(6) SS (Special shutter) & RTS (Random trigger shutter)
This camera is fitted with special shutter and random trigger
shutter function, which allows the camera to capture images
cued by external trigger input.
(7) Near-infrared region sensitivity
The CCD has a near-infrared-region sensitivity. These models
capture clear images even under near-IR shooting condition.
(8) RoHS compliant
CONFIGURATION
(1) Camera body
1
(2) Accessory
Manual
1
CONNECTION / MODE / REAR-PANEL SWITCH
(1) Connector Pin Assignment
Compatible plug: HR10A-10P-12S
(Manufactured by HIROSE ELEC.)
External sync.
Pin
No.
HD VD
VS/SYNC
R.R.
Internal sync.
1 GND GND GND
GND
2
+12V +12V +12V +12V
3 GND GND GND
GND
4
VIDEO
OUT
VIDEO
OUT
VIDEO
OUT
VIDEO OUT
5 GND GND GND
GND
6
HD IN
-----
HD IN
HD OUT*
7 VD
IN
VS/SYNC
IN
R.R. IN
VD OUT*
8 GND GND GND
GND
9
CLOCK
OUT
CLOCK
OUT
CLOCK
OUT
CLOCK
OUT
10
WEN OUT
WEN OUT
-----
WEN OUT
11
TRIG IN
TRIG IN
TRIG IN
TRIG IN
12 GND GND GND
GND
* HD VD output is available via inner SW selection under internal
sync operation.
(2) Connection Example
(3) Rear SW, Potentiometer, Connector
①
Gain adjustment potentiometer
This manual gain adjuster is enabled under Manual Gain
Control setting (Gain selection SW: MGC). Turned
clockwise, video amplification gain increases.
②
Mode selection SW
This is the camera mode selection switch.
③
75-ohm termination ON/OFF SW
This SW switches external-sync input terminal 75-ohm
termination ON/OFF. When set in right side, the
termination is 75-ohm. When set in left, it is 10k-ohm.
The initial factory setting is in OFF position.
④
HD VD IN/OUT selection SW
This is the HD VD sync-signal IN/OUT selection switch.
The status is HD VD IN when set in left side, HD VD OUT
when in right. The initial setting is EXT.
⑤
DC IN/SYNC
This connector is for DC power input, external sync signal
input, and video output, to be connected with a power supply,
sync-signal generator, and video monitor.
(4) DIP SW
[Shutter-speed Setting] X : Don’t care
No.
SHUTTER
OFF
1/125 1/250 1/500
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 OFF OFF OFF OFF
6 OFF OFF OFF OFF
7 X X X X
8 X X X X
9 X X X X
0 X X X X
No. 1/1,000 1/2,000
1/4,000 1/10,000
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 ON ON ON ON
6 OFF OFF OFF OFF
7 X X X X
8 X X X X
9 X X X X
0 X X X X
No. Flicker-less
1FLD
2FLD
4FLD
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 OFF OFF OFF OFF
6 ON ON ON ON
7 X X X X
8 X X X X
9 X X X X
0 X X X X
No. 6FLD 8FLD 10FLD
Pulse-width
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 ON ON ON ON
6 ON ON ON ON
7 X X X X
8 X X X X
9 X X X X
0 X X X X
[Mode Setting]
ＧＡＩＮ
TRIGGER
Polarity
No.
MGC AGC POSI NEGA
1
X X X X
2
X X X X
3
X X X X
4
X X X X
5
X X X X
6
X X X X
7
X X OFF ON
8
X X X X
9
X X X X
0 OFF ON
X X
Integration Mode
Gamma Correction
No.
Frame Field 1.0
0.45
1
X X X X
2
X X X X
3
X X X X
4
X X X X
5
X X X X
6
X X X X
7
X X X X
8 OFF ON
X X
9
X X OFF ON
0
X X X X
[Restart Reset / Special Shutter]
No.
Normal
Restart Reset
Special Shutter
1 OFF
ON
ON
2 OFF
ON
ON
3 OFF
ON
ON
4 OFF
ON
ON
5 OFF
ON
ON
6 OFF
ON
ON
7
X X X
8
X X X
9
X X X
0 X
X
X
[Random trigger shutter]
No.
Normal
Mode 1,2
Mode 3,4
1 OFF
OFF
OFF
2 OFF
OFF
ON
3 OFF
X X
4 OFF
X X
5 OFF
X X
6 OFF
X X
7
X X X
8
X X X
9
X X X
0 X
X
X
No.
Mode 5,6
Mode 7,8
1
OFF
ON
2
OFF OFF
3
X X
4
X X
5
X X
6
X X
7
X X
8
X X
9
X X
0
X
X
1
2
3
4
5
6
7
8
9
0
O
N
IN OUT
VIDEO OUT/
DC IN/SYNC
M GAIN
HD/VD
HIGH 75Ω
HD/VD
SHUT
FR/FL
TRIG
γ
M/AGC
①
②
③
④
⑤
CS8630BH
Rear View
EXT INT
VIDEO OUT/
DC IN/SYNC
M GAIN
HD/VD
ON OFF
75Ω
SHUT
FR/FL
TRIG
γ
M/AGC
HIGH-75Ω
VIDEO OUT
VIDEO IN
CS8630BH
Rear Panel
HD
VD/VS/SYNC/R.R
(Either one)
To be connected if necessary
Camera Cable (Option)
AC100V
50/60Hz
Camera Adapter
CA130D (Rear)
Clock Output
Video Monitor
(Rear Panel)
Video Cable
* Make sure that video output is properly 75-ohm terminated.
AC100V 50/60Hz
TRIGGER
WEN
SERIAL No.
CLOCK
OUT
VD
VIDEO OUT
HD
AC100V IN
CAMERA
TRIGGE
R
WEN
D3004765A
Using the rear-panel DIP switch, you can
make various mode setting.
Each numbered switch is OFF in LEFT
position, and ON in RIGHT position.